Users browsing this forum: 46 Guest(s)
The XU Engine |
The XU engine was fitted to a lot of 306's throughout its production. 5 variants of the engine were used in the 306 ranging from the smallest in the range, the 1.8L 16 valve (XU7JP4) to the range topping 2.0L 16 valve 167bhp GTi/Rallye engine (XU10J4RS). All Petrol engines 1.8L and above form a part of the XU range and any questions regarding these should be posted here. If you have a smaller petrol engine like the 8 valve 1.6L, this comes under the TU range which is where you should post your engine related questions. If your engine runs on diesel then there is two ranges of engine used in the 306, both of which can be found on the main forum page under the 'XUD' or 'HDi' heading. Any diesel related questions should be posted under one of these sections depending on which engine you have. |
XU Petrol Engines
|
||||||
Thread [desc] / Author | Replies | Views | Rating | Last Post | ||
Forum Announcements | ||||||
Forum changing to Read-Only - Stage 1 | - | - | - | 02-09-2021, 09:30 PM | ||
306oc Facebook Group | - | - | - | 09-08-2021, 10:15 AM | ||
Normal Threads | ||||||
Oil Cooler Rubber/Braided
11-04-2016, 07:08 PM
|
15 | 2,098 |
15-05-2016, 06:57 PM Last Post: 7057sam |
|||
Oil cooler shopping list
18-04-2016, 10:52 PM
|
7 | 2,383 |
21-04-2016, 04:51 PM Last Post: ginge191 |
|||
Oil feed return pipe?
23-10-2012, 11:45 AM
|
3 | 2,228 |
23-10-2012, 08:05 PM Last Post: burnmw |
|||
Oil getting in to the inlet
10-08-2016, 08:42 PM
|
6 | 2,055 |
18-04-2017, 05:38 PM Last Post: DeeTurbo |
|||
oil leak
19-10-2012, 12:45 PM
|
5 | 1,671 |
19-10-2012, 05:04 PM Last Post: Niall |
|||
Oil on plugs?
30-11-2014, 04:13 PM
|
9 | 1,801 |
30-11-2014, 06:06 PM Last Post: Toms306 |
|||
Oil pressure?
14-03-2014, 08:00 PM
|
4 | 912 |
14-03-2014, 10:42 PM Last Post: cully |
|||
oil temp
23-03-2014, 02:46 PM
|
9 | 1,149 |
24-03-2014, 05:28 PM Last Post: ripp444 |
|||
Oil temp question
22-07-2014, 01:44 PM
|
7 | 1,119 |
15-10-2014, 07:28 PM Last Post: Mole man |
|||
Oil temp sensor location?
06-01-2012, 05:14 PM
|
5 | 2,526 |
07-01-2012, 01:05 AM Last Post: lewisdmz |
|||
Oils
15-02-2012, 05:54 PM
|
24 | 3,981 |
24-02-2012, 12:33 AM Last Post: Rippthrough |
|||
Omex
10-09-2014, 10:47 AM
|
13 | 2,968 |
12-09-2014, 09:53 PM Last Post: jammapic |
|||
Omex in cabin
08-05-2014, 09:41 PM
|
7 | 1,945 |
17-05-2014, 08:37 PM Last Post: Niall |
|||
one to avoid!
05-02-2013, 06:58 PM
|
12 | 2,652 |
05-02-2013, 09:52 PM Last Post: puglove |
|||
only firing on 2 cylinders ?
15-11-2012, 08:50 AM
|
29 | 5,690 |
20-11-2012, 10:38 AM Last Post: davalav |
|||
opinions on megasquirt ms2 v3
(Pages:
1
2
)
09-08-2013, 09:57 AM
|
38 | 8,108 |
15-08-2013, 01:52 PM Last Post: Rippthrough |
|||
optimum inlet length - cammed / itb gti6
13-11-2013, 10:11 AM
|
11 | 2,860 |
21-05-2014, 09:01 PM Last Post: jammapic |
|||
over heating
18-11-2013, 11:28 PM
|
3 | 1,073 |
19-11-2013, 10:21 PM Last Post: Toms306 |
|||
Over revving?
16-11-2013, 11:13 PM
|
18 | 2,508 |
18-11-2013, 11:32 PM Last Post: Niall |
|||
Oversize XU10J4R Pistons
21-10-2017, 10:45 AM
|
0 | 1,239 |
21-10-2017, 10:45 AM Last Post: Mighty306 |
|||
Oversized valves for XU10J4RS
21-02-2018, 08:48 AM
|
1 | 960 |
21-02-2018, 09:25 PM Last Post: welshpug |
|||
overtemp
26-07-2013, 10:00 PM
|
3 | 1,370 |
30-07-2013, 11:08 AM Last Post: benben |
|||
Painting fuel rail
12-10-2017, 10:52 AM
|
3 | 1,322 |
12-10-2017, 01:52 PM Last Post: Mighty306 |
|||
Parts for the '6
14-05-2016, 11:24 AM
|
10 | 2,122 |
19-05-2016, 06:43 AM Last Post: DeeTurbo |
|||
parts needed/cost of full build ?
07-10-2015, 07:11 PM
|
5 | 952 |
10-10-2015, 02:36 PM Last Post: jjenn20 |
|||
- New Posts
- Hot Thread (New)
- Hot Thread (No New)
- No New Posts
- Contains Posts by You
- Closed Thread