Project 16v #theLEMOAN

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Project 16v #theLEMOAN
#61
These heads are normally absolutely disgusting when you first get them! To the point my initial attack normally involves the pressure washer straight to the ports!

Good to see another 16v build going on, lost count of them all now!
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |

[Image: sigi-2.png]
Reply
Thanks given by:
#62
(17-08-2016, 08:02 PM)darrenjlobb Wrote: These heads are normally absolutely disgusting when you first get them! To the point my initial attack normally involves the pressure washer straight to the ports!

Good to see another 16v build going on, lost count of them all now!

Haha...tizz exactly what i did :lmao

Those inlets were horrid! Flipping egr

See post #26 for the head being blasted
Wishes for more power...
Reply
Thanks given by:
#63
Best get on with this really... Just lack of time.

But got in the shed and took the sheet off it the block.

Honed the bores lightly, didnt need much. Also cleaned the deck and all the flange faces and put a thread die through all the threads. Washed down with cleaner.

Need to clean the headbolt threads out and then can start reassembly finally... Maybe it will get moving then
Wishes for more power...
Reply
Thanks given by:
#64
Come on man. Taking ages. At least mone is making good progress. Oh wait its still sitting where it was 3 months ago lol


Sent from my iPhone using Tapatalk
On a break from 306oc for personal reasons. If anyone needs or wants me most of you have my number and or facebook messenger
Thanks for the good times guys n gals. I might be back. Who knows.
Reply
Thanks given by:
#65
Crank may go in tomorrow. Valves need lapping...16 of them...keep putting it off lol

Gotta get it done. Need 16v done... So can do Kev...
Wishes for more power...
Reply
Thanks given by:
#66
sod lapping, off to a machine shop and get them done properly Smile
need a part number? http://public.servicebox.peugeot.com/ and http://service.citroen.com/ will sort you out.
Reply
Thanks given by:
#67
drill and fuel pipe makes it much easier
90' 205 gti6 supercharged
05' Evo 9 IX GT

Team eaton.


Axle rebuilds please contact me for your needs.

https://www.facebook.com/axlesbystef/
Reply
Thanks given by:
#68
(04-09-2016, 09:00 PM)welshpug Wrote: sod lapping, off to a machine shop and get them done properly Smile

Lazee much? Tongue

(04-09-2016, 09:12 PM)Stef205 Wrote: drill and fuel pipe makes it much easier

Thats not a bad call...I usually use a drill tbh but no access in on these heads... But bit of rubber hose...

You genius. 

Newsflash: 

'valves getting lapped tomorrow' lol
Wishes for more power...
Reply
Thanks given by:
#69
recently did a hdi head this way luckily it was missing 8 valves ha
90' 205 gti6 supercharged
05' Evo 9 IX GT

Team eaton.


Axle rebuilds please contact me for your needs.

https://www.facebook.com/axlesbystef/
Reply
Thanks given by:
#70
Also need to fashion an adaptor for my valve spring compressor as the access is no good on this head for my tool and the springs are 25lb heavier too
Wishes for more power...
Reply
Thanks given by:
#71
not lazy at all, 3 angle seats and valves done to suit, far more accurate and it opened the throats up.

https://flic.kr/p/HsFQSZ
need a part number? http://public.servicebox.peugeot.com/ and http://service.citroen.com/ will sort you out.
Reply
Thanks given by:
#72
Nearest machine shop is a 40min drive away. So once dropped off and returned, getting close to 1.5hrs.
I'd have to do that again to get it back.
And do both trips in working hours.
And pay the stupidly extortionate bill


By which time i could have lapped the valves and rebuilt/fitted the head! lol
Wishes for more power...
Reply
Thanks given by:
#73
that work cost £40 for the valves, £56 for the seats.

its an hour from me each way.


lapping wont give you the same results.
need a part number? http://public.servicebox.peugeot.com/ and http://service.citroen.com/ will sort you out.
Reply
Thanks given by:
#74
The results I want is lapped valve seats... So yes, I'll get the result i want with doing it myself ThumbsUp
Wishes for more power...
Reply
Thanks given by:
#75
Got a pillar drill? 

Could make something like this up then.


[Image: 1217D32C-790B-4939-8620-2F91A66F5722_zps08ptfzjh.jpg]
Reply
Thanks given by:
#76
(05-09-2016, 11:09 AM)mr_fish Wrote: Got a pillar drill? 

Could make something like this up then.


[Image: 1217D32C-790B-4939-8620-2F91A66F5722_zps08ptfzjh.jpg]


This is epic
On a break from 306oc for personal reasons. If anyone needs or wants me most of you have my number and or facebook messenger
Thanks for the good times guys n gals. I might be back. Who knows.
Reply
Thanks given by:
#77
No I havnt annoyingly...coz thats bloody genius too!
Wishes for more power...
Reply
Thanks given by:
#78
Ok...this is a moment...stuff is going BACK together! Woohoo
   

Its had a bigger meaning to me than perhaps some realise. After some personal downturns recently...I've not been motivated tbh or just too in pain/exhausted.

So this is so gooooood :-)
Wishes for more power...
Reply
Thanks given by:
#79
(08-09-2016, 03:39 PM)Piggy Wrote: Its had a bigger meaning to me than perhaps some realise. After some personal downturns recently...I've not been motivated tbh or just too in pain/exhausted.

Good to see progress, I hope the personal issue isn't anything too serious, you know I'm only down the road for beer/man hugs.
Reply
Thanks given by:
#80
Getting Piggypower on national TV was a awesome pickmeup dood... Thanks Smile
Wishes for more power...
Reply
Thanks given by:
#81
   
Wishes for more power...
Reply
Thanks given by:
#82
Winning!
Reply
Thanks given by:
#83
boom!
Reply
Thanks given by:
#84
Indeed. Much winning boom.

16v pistons, cleaned. New rings. Win rods. Arp bolts. Bearings. Ready to be inserted.
Wishes for more power...
Reply
Thanks given by:
#85
You could say things are getting pretty serious ??
Reply
Thanks given by:
#86
(18-09-2016, 07:12 PM)MitchellR32 Wrote: You could say things are getting pretty serious ??

They never get serious...

Just expensive and a little crazier

Things getting sweeter.... Progress is good if a little slow...

   

   
Wishes for more power...
Reply
Thanks given by:
#87
Twin gtb2056vl? I know where there is another good one Smile
Reply
Thanks given by:
#88
Did those bolts come with the rods?


Sent from my iPhone using Tapatalk
Reply
Thanks given by: PugLee
#89
(26-09-2016, 12:00 AM)deggerz Wrote: Did those bolts come with the rods?


Sent from my iPhone using Tapatalk

Indeedamundo
Wishes for more power...
Reply
Thanks given by:
#90
https://youtu.be/DbSSToJKJeE
Wishes for more power...
Reply
Thanks given by:


Forum Jump:


Users browsing this thread: 4 Guest(s)