Posts: 1,106
Threads: 67
Joined: Apr 2014
Reputation:
5
Location: Dereham
Car Model/Spec: 306 Sedan - Ph1 Dturbo
Thanks: 1
Given 6 thank(s) in 6 post(s)
Cant remember which two wires require being swapped for the 1.6 fps to work. Anyone recall as cant find the original post and old looms been scrapped.
Also after where the power leads go for the starter. Believe it goes battery>starter>alternator but its been so long since i removed it i cant remember
![[Image: c2cb582d8ab18b8bc7524f9b24631a2a.jpg]](https://uploads.tapatalk-cdn.com/20180704/c2cb582d8ab18b8bc7524f9b24631a2a.jpg)
Sent from my BLA-L09 using Tapatalk
Justin_306DTurbo
306 Ph1 Dturbo Sedan
306 Ph1 Dturbo Estate (VNT)
Partner Ph1 (XUD Swap)
306 HDI Stage 3 Estate (RIP)
Posts: 1,748
Threads: 41
Joined: Dec 2011
Reputation:
12
Location: Midlands
Car Model/Spec: Dtractor
Thanks: 0
Given 6 thank(s) in 6 post(s)
Saw this thread and could not help but think of Counter-Strike.
Sorry I know thats absolutely no help whatsoever.
Posts: 10,864
Threads: 117
Joined: Dec 2011
Reputation:
119
Location: Southampton
Car Model/Spec: 306 HDi and friends
Thanks: 13
Given 106 thank(s) in 106 post(s)
Battery-starter-alternator is correct. Can't remember which wires need to be swapped on the frps, sorry.
Posts: 1,106
Threads: 67
Joined: Apr 2014
Reputation:
5
Location: Dereham
Car Model/Spec: 306 Sedan - Ph1 Dturbo
Thanks: 1
Given 6 thank(s) in 6 post(s)
(06-07-2018, 06:30 PM)Poodle Wrote: Battery-starter-alternator is correct. Can't remember which wires need to be swapped on the frps, sorry.
Thank you!
Sent from my BLA-L09 using Tapatalk
Justin_306DTurbo
306 Ph1 Dturbo Sedan
306 Ph1 Dturbo Estate (VNT)
Partner Ph1 (XUD Swap)
306 HDI Stage 3 Estate (RIP)
Posts: 746
Threads: 49
Joined: Dec 2013
Reputation:
2
Location: Pie eating land.
Car Model/Spec: 306 HDI Estate + 205 HDI
Thanks: 5
Given 14 thank(s) in 14 post(s)
Never swapped the sensor over but I believe it's wires 1 + 2 need swapping. I think wire 3 is +5v.
Posts: 1,106
Threads: 67
Joined: Apr 2014
Reputation:
5
Location: Dereham
Car Model/Spec: 306 Sedan - Ph1 Dturbo
Thanks: 1
Given 6 thank(s) in 6 post(s)
(22-07-2018, 10:58 AM)Uberderv Wrote: Never swapped the sensor over but I believe it's wires 1 + 2 need swapping. I think wire 3 is +5v.
Am i right in thinking that the wires needed swapping then for the 1800 bar fps swear i read it somewhere ages ago
Sent from my BLA-L09 using Tapatalk
Justin_306DTurbo
306 Ph1 Dturbo Sedan
306 Ph1 Dturbo Estate (VNT)
Partner Ph1 (XUD Swap)
306 HDI Stage 3 Estate (RIP)
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation:
83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
Thanks: 2
Given 41 thank(s) in 41 post(s)
25-07-2018, 11:38 AM
(This post was last modified: 25-07-2018, 12:04 PM by Ruan.)
Yes that's right - if you're using a 1920.GW from a 1.6HDi you need to swap wires, the pinout is different.
Can't remember which wires need swapping though.
EDIT: Because I'm really good to you, just went and found diagrams -
1.6HDi
1 - Ground
2 - Signal
3 - +5v
2.0 8v HDi
1 - Signal
2 - Ground
3 - +5v
So in answer, yes, 1 & 2 need swapping.
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. 
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
![[Image: 22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg]](http://i585.photobucket.com/albums/ss299/Ha11elujaz0rs/22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg)
