Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
Hi guys,
Anyone know the specs for 306 bleed nipples? Looking for rear calipers but fronts may be useful to others.
I didn't realise there were so many with the same size nut. 
http://www.biggred.co.uk/bleedscrews.php?pid=Bleed Screws
Posts: 1,252
Threads: 58
Joined: Jun 2014
Reputation:
5
Location: South west
Car Model/Spec: 205 gti6 supercharged
i think its m7 on the rears
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
Any idea on length? Need that as well as girth, only part I know is the nut is 8mm as I have a proper double ended nipple spanner with 8mm and 10mm ends lol.
Posts: 908
Threads: 70
Joined: May 2013
Reputation:
10
Location: Bedford
Car Model/Spec: HDi Estate
21-01-2016, 09:44 PM
(This post was last modified: 21-01-2016, 09:45 PM by tigerstyle.)
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
Servicebox doesn't list the lengths unfortunately. But they are £6.59 each to buy from the dealer lol!
Posts: 875
Threads: 145
Joined: Mar 2014
Reputation:
5
22-01-2016, 10:27 AM
(This post was last modified: 22-01-2016, 10:28 AM by pug306driver.)
Yes, really expensive from a dealer.
1.25 ish from big red.
Enquired about seal kit, not stocked and special order from pug dealer at 28 per side plus vat, they did not know what the kit contained.
Got seals ( 33 deliverd to do both sides ) and nipples from big red, the nipples for the front ( bosch caliper ) being too short, so used the longer ones for the front for now. will post part numbers next visit.
Must get some slightly shorter ones for the front, then correct ones for the rear calipers, bendix.
The front nipple just sheared off, which is what I suspected would happen, but got the remains out using mig blob and bolt method, after stripping down the caliper. The other front one came out intact after heating caliper, once stripped. They are now back on the car and bleed.
The rears are next weeks bag of sweets.
Posts: 3,539
Threads: 42
Joined: Mar 2012
Reputation:
28
seal kit contains seals and a bit of grease.
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
Servicebox pictures the seal kit, so not sure why they don't know what's in it?
I would have thought you'd know the exact specs, Mei? 
Posts: 3,539
Threads: 42
Joined: Mar 2012
Reputation:
28
m7x1.0 is all I know, I haven't bought any for a long tine but you just need to buy whatever is listed for a bendix or bosch rear caliper
fronts are 7x1.0 or 10x1.0 depending upon which caliper (8 or 11mm spanner)
Posts: 13,881
Threads: 476
Joined: Dec 2011
Reputation:
81
Location: Ipswich
Car Model/Spec: 306 Rallye
i cant even find the bits i bought for the front ones! TOo many things! D:
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation:
33
Location: London
Car Model/Spec: ZX Volcane TD
m7 for sure on the rear, stupid size thread!
can get ones too long, won't matter as will bottom out and seal regardless
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
(22-01-2016, 11:21 AM)Eeyore Wrote: i cant even find the bits i bought for the front ones! TOo many things! D:
I'm sure there's a black hole near your house, so much seems to just disappear!! 
I'm going over this afternoon so will measure on lol. May even find we have another decent one if look harder...
Posts: 95
Threads: 8
Joined: Oct 2014
Reputation:
0
22-01-2016, 12:35 PM
(This post was last modified: 22-01-2016, 12:56 PM by Pgtips.
Edit Reason: added info
)
(21-01-2016, 08:28 PM)Toms306 Wrote: Hi guys,
Anyone know the specs for 306 bleed nipples? Looking for rear calipers but fronts may be useful to others.
I didn't realise there were so many with the same size nut.
http://www.biggred.co.uk/bleedscrews.php?pid=Bleed Screws
Just measured 1 of my old rear caliper nipples & the nut is 8mm /thread width is 6.92mm (so call it 7mm as its used )& the total length is 26.07mm from the top to the sharp point
Total thread length is 10mm measured from the bottom of the nut to the bottom thread.
Posts: 95
Threads: 8
Joined: Oct 2014
Reputation:
0
[img] ![[Image: Bleed-Screw_zpsoxp7802q.jpg]](http://i1354.photobucket.com/albums/q697/pgtips3/Bleed-Screw_zpsoxp7802q.jpg) [/img]
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
Ideal, just what we're after, cheers! 
Posts: 95
Threads: 8
Joined: Oct 2014
Reputation:
0
(22-01-2016, 02:24 PM)Toms306 Wrote: Ideal, just what we're after, cheers!
Also have the fronts for the Lucas calipers if you need those aswell lol
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation:
87
Location: Suffolk
Car Model/Spec: Focus Titanium
(22-01-2016, 02:34 PM)Pgtips Wrote: (22-01-2016, 02:24 PM)Toms306 Wrote: Ideal, just what we're after, cheers!
Also have the fronts for the Lucas calipers if you need those aswell lol
I don't currently but I'm sure it could help others.
Also, after all that it looks like we have at least one decent one on the calipers Sam found, I have soaked them in WD40 and will have a go at removing them next time I'm over.
|
![[Image: avatar_zpstlcgvhg8.jpg]](http://img.photobucket.com/albums/v363/toastmonster/avatar_zpstlcgvhg8.jpg){kind=avatar}
![[Image: Bleed-Screw_zpsoxp7802q.jpg]](http://s1354.photobucket.com/user/pgtips3/media/Bleed-Screw_zpsoxp7802q.jpg.html)