Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
3.0 V6 306
#10
The issue is more the way the weight is distributed around the engine bay than the actual weight of the thing.

But then its not alot different to DT owners with massive IC's hanging over the front end and blowers sat on the gearbox etcetc.
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |

[Image: sigi-2.png]
Reply
Thanks given by:


Messages In This Thread
3.0 V6 306 - by 306gtiparts - 31-07-2014, 08:35 PM
RE: 3.0 V6 306 - by ADV_93 - 31-07-2014, 09:39 PM
RE: 3.0 V6 306 - by RetroPug - 31-07-2014, 10:28 PM
RE: 3.0 V6 306 - by 306gtiparts - 01-08-2014, 07:04 AM
RE: 3.0 V6 306 - by londondan86 - 31-07-2014, 10:10 PM
RE: 3.0 V6 306 - by Pebbles167 - 31-07-2014, 10:14 PM
RE: 3.0 V6 306 - by Niall - 31-07-2014, 10:17 PM
RE: 3.0 V6 306 - by Piggy - 01-08-2014, 05:20 AM
RE: 3.0 V6 306 - by RetroPug - 01-08-2014, 02:00 PM
RE: 3.0 V6 306 - by Grant - 01-08-2014, 06:43 AM
RE: 3.0 V6 306 - by darrenjlobb - 01-08-2014, 07:06 AM
RE: 3.0 V6 306 - by 306gtiparts - 01-08-2014, 07:09 AM
RE: 3.0 V6 306 - by silverzx - 01-08-2014, 07:58 AM
RE: 3.0 V6 306 - by 306gtiparts - 01-08-2014, 08:17 AM
RE: 3.0 V6 306 - by 1616six - 01-08-2014, 09:15 AM
RE: 3.0 V6 306 - by Pete - 01-08-2014, 08:56 AM
RE: 3.0 V6 306 - by Ruan - 01-08-2014, 02:09 PM
RE: 3.0 V6 306 - by Grant - 02-08-2014, 06:18 AM
RE: 3.0 V6 306 - by RetroPug - 02-08-2014, 04:39 PM
RE: 3.0 V6 306 - by 306gtiparts - 02-08-2014, 05:38 PM
RE: 3.0 V6 306 - by Silky - 02-08-2014, 07:37 PM
RE: 3.0 V6 306 - by 306gtiparts - 02-08-2014, 07:38 PM
RE: 3.0 V6 306 - by Silky - 02-08-2014, 07:42 PM
RE: 3.0 V6 306 - by 306gtiparts - 02-08-2014, 07:47 PM
RE: 3.0 V6 306 - by 1616six - 02-08-2014, 08:22 PM
RE: 3.0 V6 306 - by 306gtiparts - 02-08-2014, 08:26 PM
RE: 3.0 V6 306 - by 1616six - 02-08-2014, 08:51 PM
RE: 3.0 V6 306 - by 306gtiparts - 02-08-2014, 08:55 PM
RE: 3.0 V6 306 - by 1616six - 02-08-2014, 08:57 PM
RE: 3.0 V6 306 - by 306gtiparts - 02-08-2014, 09:06 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)