306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
help

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
help
Tom Offline
Living for the 205

Registered users - Donated
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation: 24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#17
13-09-2013, 11:49 AM
Run engine spray something flammable around the head/base of the inlet manifold if the engine revs up your inlet manifold gasket is leaking. Might be able to tighten them up but go easy they are so fragile its unreal.
Doesnt even own a 306.
Find
Reply
Thanks given by:


Messages In This Thread
help - by Dan306DT - 13-09-2013, 09:56 AM
RE: help - by underground375 - 13-09-2013, 10:00 AM
RE: help - by Dan306DT - 13-09-2013, 10:03 AM
RE: help - by Mac22 - 13-09-2013, 10:13 AM
RE: help - by Dan306DT - 13-09-2013, 10:16 AM
RE: help - by Mac22 - 13-09-2013, 10:18 AM
RE: help - by Dan306DT - 13-09-2013, 10:19 AM
RE: help - by Mac22 - 13-09-2013, 10:27 AM
RE: help - by Dan306DT - 13-09-2013, 10:51 AM
RE: help - by devils_fuel - 13-09-2013, 11:12 AM
RE: help - by Dan306DT - 13-09-2013, 11:16 AM
RE: help - by adamm306 - 13-09-2013, 11:17 AM
RE: help - by Dum-Dum - 13-09-2013, 11:23 AM
RE: help - by Dan306DT - 13-09-2013, 11:24 AM
RE: help - by devils_fuel - 13-09-2013, 11:28 AM
RE: help - by Dan306DT - 13-09-2013, 11:39 AM
RE: help - by Tom - 13-09-2013, 11:49 AM
RE: help - by Dan306DT - 13-09-2013, 12:03 PM
RE: help - by adamm306 - 13-09-2013, 11:50 AM
RE: help - by Tom - 13-09-2013, 12:27 PM
RE: help - by Dan306DT - 13-09-2013, 12:47 PM
RE: help - by Tom - 13-09-2013, 12:56 PM
RE: help - by Dan306DT - 13-09-2013, 12:57 PM
RE: help - by ADV_93 - 13-09-2013, 01:05 PM
RE: help - by Dan306DT - 13-09-2013, 01:09 PM
RE: help - by ADV_93 - 13-09-2013, 01:56 PM
help - by Dan306DT - 13-09-2013, 01:57 PM
RE: help - by 4WayDiablo - 14-09-2013, 07:44 AM
help - by Dan306DT - 14-09-2013, 09:06 AM
RE: help - by Tom - 14-09-2013, 10:08 AM
RE: help - by Dan306DT - 17-09-2013, 06:26 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)