XUD oil feed block thread size
306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
XUD oil feed block thread size

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
XUD oil feed block thread size
strictly_perv Offline
Living for the 306
Posts: 1,804
Threads: 129
Joined: Mar 2012
Reputation: 11
Thanks: 0
Given 0 thank(s) in 0 post(s)
#1
20-12-2012, 09:44 PM
Does anyone happen to know the thread size for the block off the top of their head? I'm trying to get a line sorted for the new blower.
Thanks
Stage 2 XUD Sedan
Find
Reply
Thanks given by:
zx_volcane Offline
Living for the ZX

Registered users - Donated
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation: 33
Location: London
Car Model/Spec: ZX Volcane TD
Thanks: 6
Given 32 thank(s) in 32 post(s)
#2
20-12-2012, 09:45 PM (This post was last modified: 20-12-2012, 09:47 PM by zx_volcane.)
yup one sec...

m16 x1.5, i put n my project thread as I knew I'd want to know again Wink
Team ZX

Arduino controlled huge turbo'd XUD'd ZX

^click for project

[Image: avatar_zpstlcgvhg8.jpg]
Find
Reply
Thanks given by:
Ruan Offline
"Gearbox Side" towards engine 4 lyf

Registered users - Donated
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation: 83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
Thanks: 2
Given 41 thank(s) in 41 post(s)
#3
21-12-2012, 06:33 PM
Be warned though, the length is odd... Best way is to use a T2 line with a compression fitting half way... Or find a banjo bolt out of a HDi as the length is the same Smile
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Find
Reply
Thanks given by:
darrenjlobb Offline
Team Chronic Boost!

Registered users - Donated
Posts: 4,605
Threads: 90
Joined: Dec 2011
Reputation: 54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Facebook Google+ Instagram YouTube
Thanks: 0
Given 20 thank(s) in 18 post(s)
#4
22-12-2012, 09:00 AM
Any banjo bolt will work using the right thread as the banjo only relies on the copper washers not the seat at the bottom, but that will work just fine Smile
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
[Image: sigi-2.png]
Website Find
Reply
Thanks given by:
swampy Offline
Starting to Live for the 306
Posts: 1,072
Threads: 57
Joined: May 2012
Reputation: 3
Location: Peterborough
Car Model/Spec: 306 s16 406 v6 Saab 93 Ttid
Thanks: 1
Given 3 thank(s) in 3 post(s)
#5
22-12-2012, 10:06 AM
I can sort a braided line to any spec you want
Find
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  What thread is fuel feed for a bosch? silverzx 8 3,716 04-02-2015, 03:51 PM
Last Post: silverzx
  temperature sensor thread size Chris_90 2 1,595 22-09-2014, 04:35 PM
Last Post: Chris_90
  GT2052V & TD04 Oil Feed Thread silverzx 7 4,121 18-07-2014, 05:02 PM
Last Post: Tom

Forum Jump:


Users browsing this thread: 1 Guest(s)