Posts: 552
	Threads: 51
	Joined: Mar 2012
	
Reputation: 
0
Location: Norwich buhh!
Car Model/Spec: '96 ph1 DTurbo 'S' 
Thanks: 0
	Given 0 thank(s) in 0 post(s)
	 
	
	
		what temperature is the cold side of my turbo where the pipe from the airbox goes on lightly to be? 
im just wondering what material i could use to make some pipe work up so i can run my airfilter to down near the bumper for better airflow.....
	
	
	
BBBOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOSSSSSSSSTTTT!!!!!!!!
	
		
	
 
 
	
	
	
		
	Posts: 1,497
	Threads: 177
	Joined: Dec 2011
	
Reputation: 
3
Location: Highlands, Scotland
Thanks: 0
	Given 0 thank(s) in 0 post(s)
	 
	
	
		Not a good idea to put the air filter any lower, best to put it in behind the headlight, it will suckup water and the slightest look at a puddle. iv destroyed one engine, strange it dident snap the rod, only put the crank in two bits
	
	
	
	
		
	
 
 
	
	
	
		
	Posts: 552
	Threads: 51
	Joined: Mar 2012
	
Reputation: 
0
Location: Norwich buhh!
Car Model/Spec: '96 ph1 DTurbo 'S' 
Thanks: 0
	Given 0 thank(s) in 0 post(s)
	 
	
	
		what diameter? and has anyone got any experience of using plastic tubing? the company i used to work with used it on the inlet on the k series but obs there not turbo dont know if it is lightly to melt, im thinking it will just wondering tbh
	
	
	
BBBOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOSSSSSSSSTTTT!!!!!!!!
	
		
	
 
 
	
	
	
		
	Posts: 3,441
	Threads: 150
	Joined: Dec 2011
	
Reputation: 
14
Location: Beccles, Suffolk
Car Model/Spec: 306 HDI
Thanks: 0
	Given 0 thank(s) in 0 post(s)
	 
	
	
		Hang on, are you putting it so it goes directly into the turbo?
You would want it to have a gap, then filter.
=====/   )====  like that
	
	
	
![[Image: 306ocsig_edited-1-1.jpg]](http://i1204.photobucket.com/albums/bb416/declantg/306ocsig_edited-1-1.jpg) 
306 HDI, soon to be XUD
 
	
		
	
 
 
	
	
	
		
	Posts: 552
	Threads: 51
	Joined: Mar 2012
	
Reputation: 
0
Location: Norwich buhh!
Car Model/Spec: '96 ph1 DTurbo 'S' 
Thanks: 0
	Given 0 thank(s) in 0 post(s)
	 
	
	
		so not a pipe ruuning straight onto the turbo with a cone filter on the end of that?
	
	
	
BBBOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOSSSSSSSSTTTT!!!!!!!!
	
		
	
 
 
	
	
	
		
	Posts: 3,441
	Threads: 150
	Joined: Dec 2011
	
Reputation: 
14
Location: Beccles, Suffolk
Car Model/Spec: 306 HDI
Thanks: 0
	Given 0 thank(s) in 0 post(s)
	 
	
	
		they way im doing it is to have some piping running from fog light to a gap just about the air filter for the turbo
	
	
	
![[Image: 306ocsig_edited-1-1.jpg]](http://i1204.photobucket.com/albums/bb416/declantg/306ocsig_edited-1-1.jpg) 
306 HDI, soon to be XUD
 
	
		
	
 
 
	
	
	
		
	Posts: 10,864
	Threads: 117
	Joined: Dec 2011
	
Reputation: 
119
Location: Southampton
Car Model/Spec: 306 HDi and friends
Thanks: 13
	Given 106 thank(s) in 106 post(s)
	 
	
	
		That would work fine Joe, but it would work better if it had a good supply of cold air, maybe from behind the headlight as dec suggests. Plastic tubing probably wouldn't be suitable as the turbo is tucked down the back of the engine in an area being pumped with heat from the engine block and exhaust manifold. Silicone doesn't cost that much these days tbf.