Posts: 133
Threads: 14
Joined: Nov 2012
Reputation:
0
Location: Aveiro, Portugal
Car Model/Spec: Vitara 1.9-xud9
Thanks: 0
Given 1 thank(s) in 1 post(s)
Setup is a
XUD9sd with a modified K04 at 1.25bars peak boost. (Turbo Dynamics build it to be max 1.5bar)
Bosch 175bar injectors. (New, less then 5000km on them)
My 9mm Bosch is "fuel screw" maxed, till it has idle problems, and then backed off a bit.
Lda mod, but not governor.
No Smoke! there is a bit, but only coming off a gear.
In general it runs great.
But am hitting EGT's of 700-800c with a quick blast through the gears.
I think the issue is Timing, as I've got the screw maxed and therefore my injection length is too long, cause the 9mm can't open the 175 injectors soon enough.
My thought are getting a 11-12mm head for the bosch, and reducing the fuel screw to reduce timing... Thoughts?
Suzuki Santana Vitara 1.9 Td (Xud9) 3Dr
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation:
48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Thanks: 2
Given 74 thank(s) in 70 post(s)
Sorry I thought you said hot lol
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Posts: 133
Threads: 14
Joined: Nov 2012
Reputation:
0
Location: Aveiro, Portugal
Car Model/Spec: Vitara 1.9-xud9
Thanks: 0
Given 1 thank(s) in 1 post(s)
(15-12-2014, 03:21 PM)Mattcheese31 Wrote: Sorry I thought you said hot lol
Its seems hot to me, for a motor thats not smoking at all.
If I'm not even pushing enough fuel to make it smoke, why the 800C EGT than?
Suzuki Santana Vitara 1.9 Td (Xud9) 3Dr
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation:
48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Thanks: 2
Given 74 thank(s) in 70 post(s)
(15-12-2014, 04:16 PM)JamesPT Wrote: (15-12-2014, 03:21 PM)Mattcheese31 Wrote: Sorry I thought you said hot lol
Its seems hot to me, for a motor thats not smoking at all.
If I'm not even pushing enough fuel to make it smoke, why the 800C EGT than?
a maxed Bosch is plenty of fuel mate believe me, i guess you've just got the boost to burn it . . .
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation:
83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
Thanks: 2
Given 41 thank(s) in 41 post(s)
What intercooling have you got? Stock intercooler?
I'd guess that the inlet temps are very high, and you're wanting more advance... I would also guess that the turbine wheel on that is quite small, causing reasonable backpressure and not allowing gas out fast enough - 700*C is acceptable, 800*C is on the limit for prolonged use...
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. 
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
