306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Best place to tap for IPP

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Best place to tap for IPP
zx_volcane Offline
Living for the ZX

Registered users - Donated
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation: 33
Location: London
Car Model/Spec: ZX Volcane TD
#1
28-09-2012, 01:28 PM (This post was last modified: 28-09-2012, 02:45 PM by zx_volcane.)
never mind, just drilled a hole in the case and tapped it out
Team ZX

Arduino controlled huge turbo'd XUD'd ZX

^click for project

[Image: avatar_zpstlcgvhg8.jpg]
Find
CJ_Derv Offline
Living for the 306
Posts: 2,612
Threads: 124
Joined: Apr 2012
Reputation: 26
Location: Some dimension
Car Model/Spec: Megane DCiR
#2
28-09-2012, 03:32 PM
was going to say you can get a fitting used when plumbing into a test bench thats what ive got from local derv specialist cost £2 and guage screw straight in Smile
[Image: J5hxCcC.jpg]
Find
zx_volcane Offline
Living for the ZX

Registered users - Donated
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation: 33
Location: London
Car Model/Spec: ZX Volcane TD
#3
28-09-2012, 03:52 PM
Lol, the wonders of knowledge eh?

I've tapped a 1/8 bsp and going to run hose to gauge in dash, prefer to do it the awkward non oem way, with added swarf bonus Wink
Team ZX

Arduino controlled huge turbo'd XUD'd ZX

^click for project

[Image: avatar_zpstlcgvhg8.jpg]
Find
Dave Offline
Windy Day = Boosted, Right?
Posts: 1,748
Threads: 41
Joined: Dec 2011
Reputation: 12
Location: Midlands
Car Model/Spec: Dtractor
#4
28-09-2012, 04:03 PM
Your pump still on the car?!

This is what I did with the pipe/gauge, although I had the pump off/half strimmed to remove the swarf that falls out into the pump!
[Image: 22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg]
Find
zx_volcane Offline
Living for the ZX

Registered users - Donated
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation: 33
Location: London
Car Model/Spec: ZX Volcane TD
#5
28-09-2012, 04:13 PM (This post was last modified: 28-09-2012, 04:15 PM by zx_volcane.)
(28-09-2012, 04:03 PM)Dave Wrote: Your pump still on the car?!

Good God no, its in a million little pieces on the bench (aka the kitchen table).

Spare pump I'm modding / building up at a snails pace, but prob all good to go back together now and see if it works!

I'm just paranoid swarf has found its way into some little orifice
Team ZX

Arduino controlled huge turbo'd XUD'd ZX

^click for project

[Image: avatar_zpstlcgvhg8.jpg]
Find


Forum Jump:


Users browsing this thread: 1 Guest(s)