Posts: 5,494
Threads: 202
Joined: Dec 2011
Reputation:
58
Location: Eastleigh
Car Model/Spec: S16 and HDi daily
Thanks: 2
Given 29 thank(s) in 28 post(s)
Does anyone on here weld cages professionally? I'm looking for a bit of advice with adding a harness bar to my OMP bolt in. What wall thickness tube do I need to use and do I need to use cold drawn tubing? Should I TIG weld it in? I'm looking to get it fitted on Sunday or at least make a good start with the door bars etc..
Welding and fabrication projects undertaken, contact me for more information.
Posts: 661
Threads: 15
Joined: Aug 2014
Reputation:
2
Location: prescott hill
Car Model/Spec: XSi
Thanks: 2
Given 18 thank(s) in 17 post(s)
Rippthrough
P1 XSi track car
2.4 LWB T4
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation:
48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Thanks: 2
Given 74 thank(s) in 70 post(s)
Yeah good call, I should say Phillip knows a bit on the subject.
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Posts: 1,950
Threads: 55
Joined: Dec 2011
Reputation:
17
Location: Rotherham
Car Model/Spec: 406 V6
Thanks: 3
Given 10 thank(s) in 10 post(s)
Minimum MSA spec is 38mm x 2.5mm or 40 x 2.0mm (you can go larger, not smaller), in cold drawn seamless or better.
MIG or TIG is fine, how well it's welded is more important than the process.
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
Posts: 1,748
Threads: 41
Joined: Dec 2011
Reputation:
12
Location: Midlands
Car Model/Spec: Dtractor
Thanks: 0
Given 6 thank(s) in 6 post(s)
Ripp does it matter if you use tube or pipe for this? IE, is that a MINIMUM pipe ID of 38mm, or is that OD?
Posts: 1,950
Threads: 55
Joined: Dec 2011
Reputation:
17
Location: Rotherham
Car Model/Spec: 406 V6
Thanks: 3
Given 10 thank(s) in 10 post(s)
29-03-2016, 01:33 PM
(This post was last modified: 29-03-2016, 01:38 PM by Rippthrough.)
That's tube dimensions, so O/D, main issue with pipe is getting something with a high enough minimum yield strength (>350n/mm^2), blue band steam pipe, etc, isn't strong enough unless you're running in series with specific cage exceptions allowing it.
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
Posts: 2,140
Threads: 128
Joined: May 2014
Reputation:
21
Location: Cardiff
Car Model/Spec: Stage3 HDi RHF5@25psi 174bhp
Thanks: 1
Given 41 thank(s) in 38 post(s)
Pfff scaffold pole be reet. Lol
Given the choice between Niall and the sheep. I would choose the sheep!
/Toseland
Posts: 5,494
Threads: 202
Joined: Dec 2011
Reputation:
58
Location: Eastleigh
Car Model/Spec: S16 and HDi daily
Thanks: 2
Given 29 thank(s) in 28 post(s)
Why didn't I think of that!
Welding and fabrication projects undertaken, contact me for more information.