306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Hose sizes

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Hose sizes
cwspellowe Offline
Lad of the Norf
Posts: 4,883
Threads: 198
Joined: Jan 2012
Reputation: 135
Location: Not near you
#1
24-04-2012, 09:47 PM
Evening fellas, does someone fancy letting me know the common hose sizes in the engine bay? ie. fuel lines, boost compensator etc? Thinking of buying new and cutting to length rather than hunting for standard used ones.
[Image: signature_zps1a02ba79.jpg]
Find
ginge191 Offline
Professional Jungle Ginger

Registered users - Donated
Posts: 8,026
Threads: 376
Joined: Dec 2011
Reputation: 38
Location: Kent
Car Model/Spec: Phase 1 GTI 6
#2
24-04-2012, 09:50 PM
For the life of me i can't remember the size, but know buying from ebay, altogether it cost me about £10. the return line's is the only different size you need.
compensator and filter hose are the same iirc
Phaes 1 GTI 6  -  Onyx Black
Find
cwspellowe Offline
Lad of the Norf
Posts: 4,883
Threads: 198
Joined: Jan 2012
Reputation: 135
Location: Not near you
#3
24-04-2012, 09:59 PM
Think it's about 10mm, and fuel lines are about 8mm?
[Image: signature_zps1a02ba79.jpg]
Find
Ruan Offline
"Gearbox Side" towards engine 4 lyf

Registered users - Donated
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation: 83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
#4
24-04-2012, 11:15 PM
6-8mm... If you buy silicon pipes you can make it all fit, I've got 6mm everywhere and it fits, you might just have to use a bit of lube to get it over some stuff...
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Find
cwspellowe Offline
Lad of the Norf
Posts: 4,883
Threads: 198
Joined: Jan 2012
Reputation: 135
Location: Not near you
#5
25-04-2012, 10:26 AM
If I went for 8mm all round it should clamp to the smaller stuff ok, right? Also the vacuum hose from pump to servo, 10mm?
[Image: signature_zps1a02ba79.jpg]
Find
Ruan Offline
"Gearbox Side" towards engine 4 lyf

Registered users - Donated
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation: 83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
#6
25-04-2012, 11:36 AM
Aye yeah.

I think vac pump to servo is 10mm aye.
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Find
ginge191 Offline
Professional Jungle Ginger

Registered users - Donated
Posts: 8,026
Threads: 376
Joined: Dec 2011
Reputation: 38
Location: Kent
Car Model/Spec: Phase 1 GTI 6
#7
25-04-2012, 11:47 AM
Fuel hose from filter to pump - http://www.ebay.co.uk/itm/8mm-5-16-R6-F ... 1e60432d8b

and leak off piping - http://www.ebay.co.uk/itm/DIESEL-LEAK-S ... 564688ab7c

found it.. Also posted in project thread. This was what I bought, was enough plus spares
Phaes 1 GTI 6  -  Onyx Black
Find


Forum Jump:


Users browsing this thread: 1 Guest(s)