|
Gti-6 manifold
|
29-12-2014, 04:38 PM
Good afternoon to my fellow peugeot fans I have a small problem with my plan. Iv got 2L 16v xsi and I have complete inlet manifold from the 6 to go on. Iv looked at the guide on here and am handy with the spanners. The guide says half a meter of 6 mm petrol pipe and half a meter of 8mm. But I can only get 9.5mm and 7mm will this be ok? Many thanks . Xsikid
29-12-2014, 04:54 PM
29-12-2014, 04:57 PM
(29-12-2014, 04:38 PM)Xsikid Wrote: Good afternoon to my fellow peugeot fans I have a small problem with my plan. Iv got 2L 16v xsi and I have complete inlet manifold from the 6 to go on. Iv looked at the guide on here and am handy with the spanners. The guide says half a meter of 6 mm petrol pipe and half a meter of 8mm. But I can only get 9.5mm and 7mm will this be ok? Many thanks . Xsikid Try This.
29-12-2014, 05:00 PM
Coolio thank you was just in a hurry because mot is tomorrow and I was near halfrauds. Think I will wait till after mot and order from demon tweeks
29-12-2014, 06:19 PM
Halfords stock alot more sizes than that. Have you tried a different branch?
Posts: 20,092
Threads: 591 Joined: Nov 2012 Reputation: 54 Location: Cotswolds Car Model/Spec: Stage 13 16v HDi 
29-12-2014, 06:40 PM
motor factors.
Halfrauds suck hairy hamster tails Wishes for more power...
(29-12-2014, 06:19 PM)Dum-Dum Wrote: Halfords stock alot more sizes than that. Have you tried a different branch? They had more sizes but not all suitable for injection only had 3 sizes for injection. Iv ordered them now so will be ready to fit it all when back from mot ?? (29-12-2014, 06:40 PM)Piggy Wrote: motor factors. Yeah they aren't as good as they used to be but it was on my way home so thought I would give em a try! My bad lol. Hopefully get the inlet on asap after tomoz yippeeeeeeeee
29-12-2014, 06:59 PM
They (up until 3 months ago at least) Used to stock 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5 and 10mm in injection hose in 1m coils.
29-12-2014, 07:53 PM
(29-12-2014, 06:59 PM)Dum-Dum Wrote: They (up until 3 months ago at least) Used to stock 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5 and 10mm in injection hose in 1m coils. Maybe just not at slough mate. But Iv ordered through demon tweeks now so fingers crossed they come soon! Looking forward to getting the inlet fitted then onto cams next 
29-12-2014, 10:11 PM
(29-12-2014, 04:54 PM)bigcheez2k3 Wrote: http://www.scan.co.uk/products/2tb-seaga...ms-oem-ncq mah if you have to go for Seagate, at least get something from the cheetah range 
30-12-2014, 06:34 PM
If I'd realised you were in Windsor I've still got half a meter of each left from when I did mine and decent jubilee clips.
30-12-2014, 07:07 PM
31-12-2014, 12:07 AM
Right. Top tip. There are several grades of fuel line. If you get the wrong type they will perish. I've bought the wrong stuff countless times. Check to see what grade it is. Most are only low pressure applications.
The stuff in packs at my local halfwords was over priced and the wrong grade!
31-12-2014, 09:05 AM
(31-12-2014, 12:07 AM)SRowell Wrote: Right. Top tip. There are several grades of fuel line. If you get the wrong type they will perish. I've bought the wrong stuff countless times. Check to see what grade it is. Most are only low pressure applications. Unfortunately with higher percentages of ethanol being used in unleaded fuel these days any rubber based hose will degrade over time.
31-12-2014, 02:31 PM
(31-12-2014, 12:07 AM)SRowell Wrote: Right. Top tip. There are several grades of fuel line. If you get the wrong type they will perish. I've bought the wrong stuff countless times. Check to see what grade it is. Most are only low pressure applications. I ordered from demon tweeks and its 145 psi with 450 bursting pressure!! Thanks for top tip though |
|
« Next Oldest | Next Newest »
|
![[Image: Eq4gGTq.png]](http://i.imgur.com/Eq4gGTq.png)
