Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
15-09-2013, 01:19 PM
(This post was last modified: 15-09-2013, 01:20 PM by Tyronnster.)
Got my Bosch fitted earlier in the week an just sorting the fine tuning but I'm a bit stuck,
Nothing seems to happen until the throttle is about half way. My old bosch u only had to touch the throttle an would rev the arse off
Bit stuck on what to do etc
It will start an idle (a bit rough) but when messing with throttle doesn't seem to respond
Any help
(I know there is guide but I am really thick)
Posts: 1,497
Threads: 177
Joined: Dec 2011
Reputation:
3
Location: Highlands, Scotland
Has the throttle lever been put on the correct spline?
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation:
54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
got the throttle arm on the right splines??
Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
Any pics of what should look like,
Sorry for thick questions but I'm piss soaked wet from. Being outside
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation:
54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
You wont tell from a pic.
But did you put the throttle arm on yourself?...if so, how?
is it a standard 9mm?
Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
15-09-2013, 01:28 PM
(This post was last modified: 15-09-2013, 01:33 PM by Tyronnster.)
I didn't do the conversion jenks did,
It feels like there is nothing till half way.
Will get video uloaded
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation:
54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
is there no resistance at all and no engine change at all with the first movement of the arm?
Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
Nah nothing when first press it the video looks like there is a delay lol
Video uploading now excuse noisey idler lol
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation:
54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
at full throttle...is it ACTUALLY full throttle!?
Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
15-09-2013, 01:40 PM
(This post was last modified: 15-09-2013, 01:43 PM by Tyronnster.)
No it don't work 2 mins uploading elsewhere
Posts: 1,497
Threads: 177
Joined: Dec 2011
Reputation:
3
Location: Highlands, Scotland
15-09-2013, 01:47 PM
(This post was last modified: 15-09-2013, 01:48 PM by Daniel306.)
Try removing the arm and turning the spline clockwise one or two splines in relation to the arm and bolt it back up
just remember to mark it so that you can put it back how it was if needed
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation:
54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
^^^ yeah this for sure.
mark arm to the slot in the shaft for future ref
remove arm bolt.
Take arm just above splines.
get screwdriver on to the shaft, turn it clockwise till it stops. drop arm back on splines. bolt back on.
try it!
Posts: 755
Threads: 39
Joined: Jul 2013
Reputation:
4
Location: Portsmouth
Car Model/Spec: P2 Dturbo
mine did this when i turned down the max fuel to much
00' 106 Indy - Moonstone - Sold
97' 106 XT 1.6 - Mayerling Green - Swapped
95' 306 P1 DT - Onyx - Scrapped
97' 306 P2 DT - Silver - Scrapped
97' 306 P2 DT - Onyx - SORN awaiting scrap
Posts: 4,608
Threads: 90
Joined: Dec 2011
Reputation:
54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Looks like you need WAY more max fuel....
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
![[Image: sigi-2.png]](http://i281.photobucket.com/albums/kk226/darrenjlobb/sigi-2.png)
Posts: 755
Threads: 39
Joined: Jul 2013
Reputation:
4
Location: Portsmouth
Car Model/Spec: P2 Dturbo
(15-09-2013, 04:13 PM)darrenjlobb Wrote: Looks like you need WAY more max fuel....
yep funnily enough got a video on my phone of mine doing this exact thing turns out i turned the fuel down to much wind it in a bit and itll be fine
00' 106 Indy - Moonstone - Sold
97' 106 XT 1.6 - Mayerling Green - Swapped
95' 306 P1 DT - Onyx - Scrapped
97' 306 P2 DT - Silver - Scrapped
97' 306 P2 DT - Onyx - SORN awaiting scrap
Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
Thanks boys will have a look.
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation:
24
Location: Cornwall
Car Model/Spec: A3 TDi
Yeah more max fuel or wind in a minimum throttle travel screw to take up the slack.
Doesnt even own a 306.
Posts: 1,286
Threads: 132
Joined: Oct 2012
Reputation:
4
Really appreciate it all working now.
Fook me that's fast Lol
Rep when on pc
