07-05-2020, 10:49 PM
Right folks, been really busy with getting the front end ready for the engine [emoji3061] I never want to be stripping under-seal from arches ever again! But the mains thing is, the job is DONE!!!
It appeared to me that someone had undersealed over the rust, so I made it essential to strip everything down to bare metal and to treat whatever rust may be there..
Some before’s prior to stripping the under-seal.
As you can see its not a pretty sight, the car was rode without arch liners well before I bought it, ( 4 years ago ) and then had lay abandoned outside for 2 years so I wasn’t expecting any less.
![[Image: 8afa71682de276de2615fad2d97c7814.jpg]](https://uploads.tapatalk-cdn.com/20200507/8afa71682de276de2615fad2d97c7814.jpg)
![[Image: d6bc61bcff83ebe197768a9ead686418.jpg]](https://uploads.tapatalk-cdn.com/20200507/d6bc61bcff83ebe197768a9ead686418.jpg)
Looking a little better with the under-seal stripped off, and a good twist knot wire wheeling overall followed by some ‘Hammerite Rust Remover Gel’, wash that off and its good for painting once fully dried! ( I used an air line to blow out any water that may been laying within the creases.
![[Image: f99625c14b83488bc35ea2cef8c8c490.jpg]](https://uploads.tapatalk-cdn.com/20200507/f99625c14b83488bc35ea2cef8c8c490.jpg)
Full front end treated, prepared and ready for some etch’ing primer! The stage I thought I would never see lol [emoji1787]
![[Image: d4c23c4e01db815070e06a77ee351907.jpg]](https://uploads.tapatalk-cdn.com/20200507/d4c23c4e01db815070e06a77ee351907.jpg)
Primer [emoji736] (2/3 coats)
![[Image: c93e54303528e568ec92e3e41727442d.jpg]](https://uploads.tapatalk-cdn.com/20200507/c93e54303528e568ec92e3e41727442d.jpg)
![[Image: 66a4cc3fe6616073a82f87b090240f4a.jpg]](https://uploads.tapatalk-cdn.com/20200507/66a4cc3fe6616073a82f87b090240f4a.jpg)
![[Image: 637ca680cfccab718f6d91466869544c.jpg]](https://uploads.tapatalk-cdn.com/20200507/637ca680cfccab718f6d91466869544c.jpg)
![[Image: 4ca5e084a606ede4f0cc0c52f21ebaff.jpg]](https://uploads.tapatalk-cdn.com/20200507/4ca5e084a606ede4f0cc0c52f21ebaff.jpg)
Next up was to seam seal, I would say this is the most important part of redoing any area of your cars chassis etc.
I spent a little less time being neat on the arches as these areas wont be seen. Will tidy up with paint and waxoyl anyways [emoji3526]!
![[Image: 03970043aaa2cebdca2e865931709093.jpg]](https://uploads.tapatalk-cdn.com/20200507/03970043aaa2cebdca2e865931709093.jpg)
Sent from my iPhone using Tapatalk
It appeared to me that someone had undersealed over the rust, so I made it essential to strip everything down to bare metal and to treat whatever rust may be there..
Some before’s prior to stripping the under-seal.
As you can see its not a pretty sight, the car was rode without arch liners well before I bought it, ( 4 years ago ) and then had lay abandoned outside for 2 years so I wasn’t expecting any less.
![[Image: 8afa71682de276de2615fad2d97c7814.jpg]](https://uploads.tapatalk-cdn.com/20200507/8afa71682de276de2615fad2d97c7814.jpg)
![[Image: d6bc61bcff83ebe197768a9ead686418.jpg]](https://uploads.tapatalk-cdn.com/20200507/d6bc61bcff83ebe197768a9ead686418.jpg)
Looking a little better with the under-seal stripped off, and a good twist knot wire wheeling overall followed by some ‘Hammerite Rust Remover Gel’, wash that off and its good for painting once fully dried! ( I used an air line to blow out any water that may been laying within the creases.
![[Image: f99625c14b83488bc35ea2cef8c8c490.jpg]](https://uploads.tapatalk-cdn.com/20200507/f99625c14b83488bc35ea2cef8c8c490.jpg)
Full front end treated, prepared and ready for some etch’ing primer! The stage I thought I would never see lol [emoji1787]
![[Image: d4c23c4e01db815070e06a77ee351907.jpg]](https://uploads.tapatalk-cdn.com/20200507/d4c23c4e01db815070e06a77ee351907.jpg)
Primer [emoji736] (2/3 coats)
![[Image: c93e54303528e568ec92e3e41727442d.jpg]](https://uploads.tapatalk-cdn.com/20200507/c93e54303528e568ec92e3e41727442d.jpg)
![[Image: 66a4cc3fe6616073a82f87b090240f4a.jpg]](https://uploads.tapatalk-cdn.com/20200507/66a4cc3fe6616073a82f87b090240f4a.jpg)
![[Image: 637ca680cfccab718f6d91466869544c.jpg]](https://uploads.tapatalk-cdn.com/20200507/637ca680cfccab718f6d91466869544c.jpg)
![[Image: 4ca5e084a606ede4f0cc0c52f21ebaff.jpg]](https://uploads.tapatalk-cdn.com/20200507/4ca5e084a606ede4f0cc0c52f21ebaff.jpg)
Next up was to seam seal, I would say this is the most important part of redoing any area of your cars chassis etc.
I spent a little less time being neat on the arches as these areas wont be seen. Will tidy up with paint and waxoyl anyways [emoji3526]!
![[Image: 03970043aaa2cebdca2e865931709093.jpg]](https://uploads.tapatalk-cdn.com/20200507/03970043aaa2cebdca2e865931709093.jpg)
Sent from my iPhone using Tapatalk