04-01-2013, 04:20 PM
Finaly starting to get ready for dropping an engine into her, so stripped the k14-2 for a rebuild
turbo split
![[Image: IMG-20130104-00013_zps4c08aedf.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00013_zps4c08aedf.jpg)
intake side turbine
![[Image: IMG-20130104-00015_zps83c47301.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00015_zps83c47301.jpg)
exhaust side turbine
![[Image: IMG-20130104-00016_zps67528577.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00016_zps67528577.jpg)
![[Image: IMG-20130104-00017_zps69fecef7.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00017_zps69fecef7.jpg)
exhaust turbine housing
![[Image: IMG-20130104-00014_zpscb25c69a.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00014_zpscb25c69a.jpg)
both turbine wheels have got abit of scoring on them, they arnt that bad but, plan is to rebuild it with 360 bearings, ream out the hotside and make a new downpipe
the turbo was very late spooling before so trying to make it abit easier to spool
http://www.turborebuild.co.uk/p/product/...e+bearing/
also is that all i need for the rebuild? aslong as the shaft is ok once its split?
turbo split
![[Image: IMG-20130104-00013_zps4c08aedf.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00013_zps4c08aedf.jpg)
intake side turbine
![[Image: IMG-20130104-00015_zps83c47301.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00015_zps83c47301.jpg)
exhaust side turbine
![[Image: IMG-20130104-00016_zps67528577.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00016_zps67528577.jpg)
![[Image: IMG-20130104-00017_zps69fecef7.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00017_zps69fecef7.jpg)
exhaust turbine housing
![[Image: IMG-20130104-00014_zpscb25c69a.jpg]](http://i157.photobucket.com/albums/t55/lilricky64/ILZ%20Engine%20built/IMG-20130104-00014_zpscb25c69a.jpg)
both turbine wheels have got abit of scoring on them, they arnt that bad but, plan is to rebuild it with 360 bearings, ream out the hotside and make a new downpipe
the turbo was very late spooling before so trying to make it abit easier to spool
http://www.turborebuild.co.uk/p/product/...e+bearing/
also is that all i need for the rebuild? aslong as the shaft is ok once its split?