FCS - So what have you got left to do?

[Niall]

Well its now just over a month until FCS, probably the biggest show of the year for this club and I'm sure most people have got a lot of preparation to do to their french shit boxes. So what have you got left to do?

Ive got to change the sump, service it, fit the new charger outlet and boost piping re routing, tidy up loom and give the car a good detailing as its a right state. Also if i get the time, re paint the callipers as i got brake fluid on them

[Dum-Dum]

Fit FMIC, fit passenger bucket, fit ph1 rad and lower hose remove rear thermostat, fit fan, make rev counter work, put grub screws in roof, stop leaks through roof, fix fuel tank leak, put dehumidifier in car, refit front end without cable ties.

Just a little list lol

If i could get the rad and lower hose done id actually have some motivation to do the rest.

[darrenjlobb]

Hmm, Nothing

The joys of not taking silly tri blown dervs to car shows, haha

[bigcheez2k3]

As I mention (a lot) get hte bloody thing fixed. Still sitting on my driveway with the dent. Declared as 'unroadworthy' (despite the fat they let me use it for 2 weeks before deciding this) so can't use it at all until fixed and I've sent Flux some proof.

No point booking my tickets til it's done either.

[Niall]

Hmm, Nothing

The joys of not taking silly tri blown dervs to car shows, haha

Going to miss having that car there! I really do hope you have a surprise up your sleeve! lol

[lolsteve]

Sort head gasket out
Get exhaust cam reprofiled
Fit offset dowels
Service
Track day/daily wheels as the nankangs are starting to look a little worse for wear on the edges
Fit manifold + sports cat or get cat welded onto decat pipe

[zx_volcane]

Doesn't sound like a long time :/

Have booked a little tiny 15min track slot, so may make some choice mods for that

Sort out the soggy back end by changing the axle out (cba)
Fit big rad
Poss put an oil cooler on


Other than that just a bit of spit n polish

[ginge191]

Wishbones
Bonnet
grill and sticks
Wheels
ARB
Engine mounts
Rear mounts
Exhaust
plan the boost next year over many pints at the show

[Niall]

Wishbones
Bonnet
grill and sticks
Wheels
ARB
Engine mounts
Rear mounts
Exhaust
plan the boost next year over many pints at the show

Make your bloody mind up! Thought you was selling it?

[bashbarnard]

If I can go. Nothing! I have a full by working nothing to do Peugeot 306. Maybe find and fit Bosch before show though

[Dum-Dum]

Wishbones
Bonnet
grill and sticks
Wheels
ARB
Engine mounts
Rear mounts
Exhaust
plan the boost next year over many pints at the show

Glad I'm not the only one with a bloody long list.

After I've done that I've got the bloody rallye to start on too as I'd like that roadworthy before winter.

[Grant]

Wash it
Make sure it starts
Pray I make it there

[bashbarnard]

Also buy a ticket

[Niall]

Oh yeah forgot to say, make sure i have a stock of bottom end bearings and RAC cover.

[mikey b]

Lots need to make a list get it running get 11mm on get mot and tax and so on

[Matt]

To be fair my list is of vital stuff to sort

Fit wheels (all painted just need fitting)
Bumper adjustments wet sand the rear to rid the peel!
lowering springs Here to fit (cba to do myself as lazy with compressors)
Bosch pump to fit (just waiting on either payday or a loan haha)
Need to buy a rear beam and lower
Get some spacers (again waiting on payday)
Refit interior (freeeeeeeee)


Everything I need to be done will cost just shy of £150 it's just I cba to do it, or have to drive miles to get the parts

[Eeyore]

Not much to do...

cleaning the car
fitting new brake pads, callipers, discs and braided lines
rewiring the engine loom and fitting and mapping an OMEX 600 ecu.
Fitting a gti6 sump
Fitting a gti6 exhaust manifold and full stainless system.
Fitting throttlebodies.
Making new custom rear boot dividers
Relocating the power steering
full service
new tyres balancing, fitting
spray painting all the exterior and interior plastics...

hardly anything at all! D:

[Nathan1305]

I need to...

Tax it
Insure it
Need to get a new ICV ( has anyone got one?)
Fit new exhaust
fit induction kit
Service

And being a peugeot probably more things will go wrong

[Slam Wagon]

Respray wheels - maybe
Ninja plans - most likely
Sort out sub/boot build - start tomorrow
Plumb in gauges - maybe
Clean it - should really
Tidy engine bay - maybe
Dyno it - maybe

All the other things i think of, still plenty of time for more stupid ideas, maybe new splitter and add some aero for lols.

[Dum-Dum]

^^^ I might add my splitter too but it'll catch on the camber of the road however for lol value its a winner

[ozonehostile]

Erm
Wait for new suspension bits to arrive and fit
Change Wishbones + all other front end gubbins like track rod ends and Droplinks

Get my ph3 strips painted + sort the scuff on the front bumper

Fit rallye aux setup

Engine bay details

Change bottom engine mount

Get tyres swapped over

Fit ph1 interior

Service engine

Blackmasks

Polish the life out of it

[Slam Wagon]

^^^ I might add my splitter too but it'll catch on the camber of the road however for lol value its a winner

But of rubbing is all good, get the attention.

[lolsteve]

Have booked a little tiny 15min track slot, so may make some choice mods for that

What time slot?

[zx_volcane]

Have booked a little tiny 15min track slot, so may make some choice mods for that

What time slot?

2pm ish?

[vlj]

Attend

[7057sam]

Fit oil cooler
Get it tracked
New pads might be a picky and just get decent front ones
clean it
Fit the cams and wait for it to go bang

[kentiiboii]

Here we go...
Finish cam belt
Fit rallye aux setup
New front bumper
Crystal headlights
Mask headlights
Paint badges
Fit baker bm engine mounts when arrived
Fit omp corcisa steering wheel
Change front speakers
Fit sub
Gti6 splitter
Undercoat
Arch liners
Clean interior
Trip to scrap yard for missing bits
Detail outside
Engine detail
Mot the car
Tax the car

Hopefully it wont die!

[Matt]

Fit omp corcisa steering wheel

Don't you have grants fake wheel??

[Dum-Dum]

^^^ I might add my splitter too but it'll catch on the camber of the road however for lol value its a winner

But of rubbing is all good, get the attention.

Not if it catches too badly and breaks the cable ties holding the bumper on lol

[Atterz]

Well i need a twin plate clutch ready to handle 540lbft of torque after the new injectors/turbo is fitted. Otherwise nothing, o wait, i wont be there, ill be getting a tan somewhere else .

Have fun guys, catch up with you at Christmas time hopefully!