Posts: 170
Threads: 19
Joined: Jul 2013
Reputation:
1
Location: Scotland, Strathaven/ East Kilbride
Car Model/Spec: phase 1 sedan SLDT
Thanks: 0
Given 0 thank(s) in 0 post(s)
Can anyone tell me (or point me to another thread if it's been covered) at what boost pressure the standard K14 starts to just generate hot air and not improve performance?
I don't want to be running the turbo pointlessly hard but I'm pretty sure I can convince myself that the higher the boost pressure the faster the car feels. It's currently running about 24psi on the standard top mount, boost just controlled by fuelling. Can turn it up to run higher but don't want to needlessly destroy anything if there are no real gains.
Thanks.
Posts: 616
Threads: 62
Joined: Jul 2013
Reputation:
1
Location: South Wales
Car Model/Spec: Megane 265 + SHB Gti 6
Thanks: 1
Given 6 thank(s) in 6 post(s)
14-01-2014, 01:33 PM
(This post was last modified: 14-01-2014, 01:33 PM by Lwilliams.)
On a top mount mate I would say no... around 22 psi is what I have noticed people run on here some with front mount some without.... if your still on standard rods I wouldn't want to be pushing it much more anyway unless reliabilty is not an issue...
Hope this helps
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation:
48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Thanks: 2
Given 74 thank(s) in 70 post(s)
my k14 is about 22-24psi and kicks out the power shown below in my sig, wouldn't go much higher myself, think it's about right . .
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Posts: 170
Threads: 19
Joined: Jul 2013
Reputation:
1
Location: Scotland, Strathaven/ East Kilbride
Car Model/Spec: phase 1 sedan SLDT
Thanks: 0
Given 0 thank(s) in 0 post(s)
Ideal, thanks. Will fit front mount before the warmer weather to keep temps down a bit but don't plan to change turbo until the rods are done now. Have probably just been reading too much on here but this is my sensible car so don't really want to break it.
Posts: 5
Threads: 0
Joined: Feb 2014
Thanks: 0
Given 0 thank(s) in 0 post(s)
What rod shall i run with k14 turbo??
Posts: 5
Threads: 0
Joined: Feb 2014
Thanks: 0
Given 0 thank(s) in 0 post(s)
Con rods.... Im picking one up this week as mine has gone but dont know if i would have to change the rods around
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation:
24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
Your picking up one what because your what has gone? Where has it gone? You dont need to change the conrods... People do because xud ones are weak. But you dont have to.
Doesnt even own a 306.
Posts: 5
Threads: 0
Joined: Feb 2014
Thanks: 0
Given 0 thank(s) in 0 post(s)
My turbo has blown up, and picking up a k14 turbo soon, and what rods will i have to change to the hdi rods?
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation:
24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
Hdi rods are no sure thing either. They are a bit stronger and a bit bigger but tbh i doubt your going to have any issues, its only a K14.
Doesnt even own a 306.
Posts: 26
Threads: 3
Joined: Jan 2014
Thanks: 0
Given 0 thank(s) in 0 post(s)
No need for any internal engine mods. Fire on your new turbo & enjoy it.
Posts: 5
Threads: 0
Joined: Feb 2014
Thanks: 0
Given 0 thank(s) in 0 post(s)
On a lucas pump whats the reconmened boost psi i should run on the k14 with fmic?
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation:
48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Thanks: 2
Given 74 thank(s) in 70 post(s)
(04-02-2014, 12:05 AM)colzyxx Wrote: On a lucas pump whats the reconmened boost psi i should run on the k14 with fmic?
Its not that simple really, as a ballpark I'd say 20-25psi...
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Posts: 5
Threads: 0
Joined: Feb 2014
Thanks: 0
Given 0 thank(s) in 0 post(s)
Im just new to the 306 tuning trying to get advice haha, was running stnadard turbo at 19psi and now the turbo went bamg ooops!!!
