Xud9SD and TE crankshafts. - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: Engines (https://www.306oc.co.uk/forum/forumdisplay.php?fid=16) +--- Forum: XUD Section (https://www.306oc.co.uk/forum/forumdisplay.php?fid=11) +--- Thread: Xud9SD and TE crankshafts. (/showthread.php?tid=30247) |
Xud9SD and TE crankshafts. - JamesPT - 28-04-2015 Quick question to the Guru's! Are Xud9SD and XUD9TE crankshafts (Cast vs Forged) compatible? Also, same question for Camshafts? (the TE's have a vacuum pump on the end, SD's don't) but other than that? I'll collecting parts for my engine rebuild, its a Suzuki Vitara with the XUD9sd 1.9 DTurbo. Stock its 72Hp, I'm well past that point. RE: Xud9SD and TE crankshafts. - Danny Wideboy - 29-04-2015 Hammer? RE: Xud9SD and TE crankshafts. - JamesPT - 31-05-2015 (29-04-2015, 06:57 PM)Danny Wideboy Wrote: Hammer? No Hammers RE: Xud9SD and TE crankshafts. - welshpug - 31-05-2015 compatible yes, the same no. RE: Xud9SD and TE crankshafts. - Ruan - 01-06-2015 One is burnished steel, the other is plain steel. As Welshpug says, compatible, yes, the same, no. RE: Xud9SD and TE crankshafts. - JamesPT - 01-06-2015 (01-06-2015, 09:49 AM)Ruan Wrote: One is burnished steel, the other is plain steel. Thanks, thats what I needed to Know, as I'm doing a Build, and may as well Drop in a Forged Crank, along with HDi rods. Oh, make it a triple Question:??? I've seen somewhere else that the DW10 is also a Drop-In compatible crank, that true? And if So, is it forged, better than the Xud9te Crank & which DW10? theres a few, what Engine code? (anyone want to sell me a Crank and Rods?) RE: Xud9SD and TE crankshafts. - Ruan - 01-06-2015 They're both forged - just one is burnished. DW10TD/RHY = Plain Steel like XUD7/XUD9SD DW10TED/RHZ = Burnished Steel like XUD9TE. I've seen DW10TDs which use XUD7/XUD9SD Plain steel crank @ 220hp+ on the original crank, you'll run into other issues long before you get crank issues, I've never seen one fail. RE: Xud9SD and TE crankshafts. - darrenjlobb - 02-06-2015 I have multiple sets of hdi rods for sale if you need some. RE: Xud9SD and TE crankshafts. - JamesPT - 02-06-2015 (01-06-2015, 02:22 PM)Ruan Wrote: They're both forged - just one is burnished. 200hp+..Plain Steel:...Agreed, but if I'm doing a bottom to top rebuild, it doesn't hurt to drop in a stronger crank, even if it's only 10% better. (ie, I'm getting the rotating assembly balanced.. pulley, crank, flywheel, so may as well do it with the best possible parts.) (02-06-2015, 06:16 AM)darrenjlobb Wrote: I have multiple sets of hdi rods for sale if you need some. Just after writing my post, I think I got that sorted here, but Good to know. (You don't have Forged H-beams to sell do ya? $ $ $ $) ps. I Blame you for my Xud9 obsession! Start off watching your videos and doing minor tinkerings, now I can't stop! HELLO!! It seems like I can grab a DW10ATED/RHZ... pull its Crank & Rods attach, throw on XUD9 pistons and I'm good to go!? Flywheel bolt pattern & pulley shaft identical!(?) Sound about right? RE: Xud9SD and TE crankshafts. - Ruan - 02-06-2015 Yes you certainly can do this - the bottom ends are identical near enough in the RHZ vs RHY - just a different crank, can put XUD9 pistons on and it all fits fine. http://www.peugeot206cc.co.uk/repair-206/206/info/gb/b1bbm2k3.htm Very good document for knowing what you can and can't use out of DW10 Motors. RE: Xud9SD and TE crankshafts. - JamesPT - 25-10-2016 Question, I have a Xud9te (DHX), That would have a forged crank right? RE: Xud9SD and TE crankshafts. - Danny Wideboy - 25-10-2016 As above, all forged. Just one is burnished, you should have the right one. XUD9TE is all you need to worry about, DHY/X has nowt to do with it. |