TD04 Turbo Manifold - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: Engines (https://www.306oc.co.uk/forum/forumdisplay.php?fid=16) +--- Forum: XUD Section (https://www.306oc.co.uk/forum/forumdisplay.php?fid=11) +--- Thread: TD04 Turbo Manifold (/showthread.php?tid=15337) |
TD04 Turbo Manifold - scottbmxer - 08-07-2013 Anyone know what size/type of thread is on the td04 manifold? Looks like m10 but doesn't fit. Imperial? RE: TD04 Turbo Manifold - Tom - 08-07-2013 M10 x 1.25 not a regular 1.5 thread. If thats the original stud that is Re: TD04 Turbo Manifold - scottbmxer - 08-07-2013 Any idea where I can get a couple apart from eBay because you have to but a pricey pack RE: TD04 Turbo Manifold - Tom - 08-07-2013 Ummm you could try Halfords and B&Q's?? RE: TD04 Turbo Manifold - rryan - 08-07-2013 i used to live in wycombe, and always used bee-fast fasteners, in cressex industrial estate, for that kind of thing. they'll probley just give you them for free RE: TD04 Turbo Manifold - scottbmxer - 08-07-2013 Thanks for the help tom and ryan!! While I got the thread open I might as well clear up two things Will I need to blank this as I took the wastegate actuator off and weld it shut The other thing was what are these for as it already has a oil feed on the left side and return/drain on the right side (opposite) RE: TD04 Turbo Manifold - strictly_perv - 08-07-2013 Yes blank that if it the gates welded and those are the water cooling holes so ignore them lol RE: TD04 Turbo Manifold - scottbmxer - 08-07-2013 (08-07-2013, 06:59 PM)strictly_derv Wrote: Yes blank that if it the gates welded and those are the water cooling holes so ignore them lol Whats a good or easy way to blank it if you have little tools?? Ahh yes I remember forgot about the watercooling Cheers RE: TD04 Turbo Manifold - rryan - 08-07-2013 cut an inch of tubing. put one end over the pipe and zip tie/clamp a bolt in the open end, that normally works or just squash the pipe (might not seal 100% tho) and/or use chemical metal i the hole RE: TD04 Turbo Manifold - bigcheez2k3 - 09-07-2013 I got bolts for the studs from ebay, 6 for not much at all. You do need to seal that hole up, I used instant gasket in mine, then a small piece of hose with instant gasket to make sure it was sealed. Are you going to be using any gaskets? RE: TD04 Turbo Manifold - Tom - 09-07-2013 Holts firegum exhaust paste. f*ck gaskets for a laugh. I never blocked my waterholes just left them. RE: TD04 Turbo Manifold - bigcheez2k3 - 09-07-2013 (09-07-2013, 07:08 AM)Tom Wrote: Holts firegum exhaust paste. f*ck gaskets for a laugh. I never blocked my waterholes just left them. I used that and gaskets. Got a sheet of metal gasket material from eBay and cut my own. Re: TD04 Turbo Manifold - scottbmxer - 09-07-2013 I brought a gasket for the t2 manifold where it goes onto the engine but the turbo itself and all the plates - I was just planning on using holts exhaust paste as I've heard it seals a treat I'll try putting some on the small turbo pipe and capping it off with a small silicone hose, cheers RE: TD04 Turbo Manifold - bigcheez2k3 - 09-07-2013 (09-07-2013, 09:31 AM)scottbmxer Wrote: I brought a gasket for the t2 manifold where it goes onto the engine but the turbo itself and all the plates - I was just planning on using holts exhaust paste as I've heard it seals a treat I did both so I was sure it was sealed, didn't want to take it off again. |