(1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: General (https://www.306oc.co.uk/forum/forumdisplay.php?fid=6) +--- Forum: Newbies (https://www.306oc.co.uk/forum/forumdisplay.php?fid=24) +--- Thread: (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) (/showthread.php?tid=36970) |
(1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - billz888 - 13-07-2018 * Hey everyone, just made an account to get a bit more answers from the ones who might have them, so please no rubbish comments saying you cant do it, or it'll take time/work/money etc... i have till October to get myself an engine (being a 1.9dturbo - LX DT or DT? is there a difference) * im not entirely sure what the difference is... But my main concern is this.... i have a 1.9dw8 in my 306 ESTATE and have my eyes on a 405 estate to use as doner for my 306... So do i need to get the entire engine bay/gearbox/clutch/driveshafts (anything else?) Or can i do a straight engine swap and sstill use the same gearbox and clutch ?? If anyone has any questions that would be great, answers even better!! Thanks billz888 my car reg is ahz1115 p124 mkp is the car i might buy if everything on here goes well (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - bashbarnard - 13-07-2018 306 wiring loom for the engine. Plug and play that way. Phase 2 xud clocks for.rev counter Different elbow for.the turbo as turbo points different direction In 405 Downpipe You also have to pull the gearbox pin and swap for the xud one. Also you'll probably need a different clutch cable due to pull Vs push type clutch. Rad you can get away with but wouldn't advise. Try and get an xud rad as they're thicker. Also ps We don't think any engine swaps are silly here we've seen most of them. I believe piggys 2.1 started life as a 1.4 Sent from my FIG-LX1 using Tapatalk RE: (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - Piggy - 13-07-2018 Pah! 1.6 I'll have you know! And it states that way for all of one day in my ownership Be easier to find a 306 Xud9 for conversion tbh...due to all the parts needed as bash has highlighted! RE: (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - billz888 - 14-07-2018 thx bash n piggy, dont fully understand what all that means... so in simple terms im best getting an xud9 engine and box ?? cheers for the speedy replies (13-07-2018, 10:20 PM)bashbarnard Wrote: 306 wiring loom for the engine. Plug and play that way. Phase 2 xud clocks for.rev counter . (13-07-2018, 10:25 PM)Piggy Wrote: Pah! 1.6 I'll have you know! And it states that way for all of one day in my ownership . (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - bashbarnard - 14-07-2018 Best getting a 306 xud and swapping all the bits yes Sent from my FIG-LX1 using Tapatalk RE: (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - billz888 - 15-07-2018 (14-07-2018, 11:26 AM)bashbarnard Wrote: Best getting a 306 xud and swapping all the bits yes which all parts might it be ?? thanks for the feedback RE: (1st post) Need answers about dw8(1.9LX D) - xud dt(1.9LXDT) - bashbarnard - 15-07-2018 everything from the engine bay |