![]() |
gros injecteur pour xud9te - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: Engines (https://www.306oc.co.uk/forum/forumdisplay.php?fid=16) +--- Forum: XUD Section (https://www.306oc.co.uk/forum/forumdisplay.php?fid=11) +--- Thread: gros injecteur pour xud9te (/showthread.php?tid=33362) |
gros injecteur pour xud9te - niciou - 25-02-2016 Hello Are that someone has already mid larger injector on his XUD9TE engine? me I have a 2.1 liter engine with low cylinder 1.9 td I have mid dssr performance injector nose but I am not sure that they give more speed .... RE: big injecteur xud9te - zx_volcane - 25-02-2016 standard injectors are plenty capable for big power RE: big injecteur xud9te - niciou - 25-02-2016 (25-02-2016, 10:13 PM)zx_volcane Wrote: standard injectors are plenty capable for big powerits going so I want to get around the 220 hp is no problem at this level I have the head in a 11 mm I work the head enlarge , polishing, etc ... or the stuck his was the turbo I have a td04l - 15t with a casing 5 cm I wonder if I will go far with those turbo what can give me turbo 220 hp ? RE: gros injecteur pour xud9te - Piggy - 26-02-2016 So you have a 2.1 head with a 1.9 block? The 2.1 and 1.9 share the same injectors...they are good for over 200bhp if in good condition. RE: big injecteur xud9te - Piggy - 26-02-2016 Injectors be fine. Your turbo is the issue. Get a GTB2260 ![]() RE: big injecteur xud9te - niciou - 26-02-2016 (26-02-2016, 07:51 AM)Piggy Wrote: Injectors be fine.gtb2260 a more recent and probably more effective as a turbo without its electronic management which gives its autent can be obtained without electronic power management ? RE: gros injecteur pour xud9te - niciou - 26-02-2016 (26-02-2016, 07:50 AM)Piggy Wrote: So you have a 2.1 head with a 1.9 block? that a block of 2.1 l with a culassse 1.9 mi I have the nose of SRHR injector performance. http://dss-fr.com/product_info.php/dss-perf-p-56 his is what I have on the bolt 1.9 mi . RE: big injecteur xud9te - zx_volcane - 26-02-2016 (26-02-2016, 08:01 AM)niciou Wrote:(26-02-2016, 07:51 AM)Piggy Wrote: Injectors be fine.gtb2260 a more recent and probably more effective as a turbo without its electronic management which gives its autent yes, can actuate with boost actuator and mbc - won't be perfect, but doable! RE: gros injecteur pour xud9te - Piggy - 26-02-2016 Ah ok... Culasse is cylinder head in english. Hmmm interesting that you have managed to do that... Didnt know it was 100% possible till now.. Why did you go down this route? Standard 1.9/2.1 injectors are fine for the power you want RE: gros injecteur pour xud9te - cully - 26-02-2016 merged as requested ![]() RE: gros injecteur pour xud9te - bashbarnard - 26-02-2016 Want some info on the head bolting up. I've looked into it. Looks like its just the oil way that needs nodding in the 1.9 head. Everything else lines up perfect. RE: gros injecteur pour xud9te - niciou - 26-02-2016 (26-02-2016, 09:01 AM)Piggy Wrote: Ah ok... Culasse is cylinder head in english. This morning I had the déculasser j of the pressure in the water system I 'll probably do a post with my project and photos. I have half a head of the 1.9 because they told me what was more resistant to pressure and better now that cools the cylinder 12s . with the turbo conserne the idea of taking a gtb wound me but its still a big investment for now but has on I sell my td04l and will take in building automation . By cons I wonder if it will not hurt to take a gtb2256 pluto a gtb2260 that 2256 would be a better moin egt spool and may be able to reach 210 hp for reliable prepa long therm . RE: gros injecteur pour xud9te - bashbarnard - 26-02-2016 So how did you go about putting the 1.9 head on?? RE: gros injecteur pour xud9te - niciou - 26-02-2016 (26-02-2016, 03:25 PM)bashbarnard Wrote: So how did you go about putting the 1.9 head onje l espliquerai dans mon nouveau post avec les photos du moteur ce soir I l espliquerai in my new post with motor pictures tonight (26-02-2016, 03:28 PM)niciou Wrote:(26-02-2016, 03:25 PM)bashbarnard Wrote: So how did you go about putting the 1.9 head onje l espliquerai dans mon nouveau post avec les photos du moteur ce soir RE: gros injecteur pour xud9te - bashbarnard - 26-02-2016 (26-02-2016, 03:28 PM)niciou Wrote:a(26-02-2016, 03:25 PM)bashbarnard Wrote: So how did you go about putting the 1.9 head on Ok awesome. My French is limited. But I assume photos tonight with explanation of how. ![]() RE: gros injecteur pour xud9te - Xud Missile - 26-02-2016 http://www.maxrevs.co.uk/cars/peugeot/showcar.php?carId=309 1.9 head on a 2.1 block from 10 years ago ^ RE: gros injecteur pour xud9te - bashbarnard - 26-02-2016 (26-02-2016, 03:34 PM)Xud Missile Wrote: http://www.maxrevs.co.uk/cars/peugeot/showcar.php?carId=309 Yeah but there is no how to. I'm sure you just have to machine the oil ways together for 1.9 head and use a 1.9 gasket. If I can find out id rather stick a 8v head on mine as it would be easier for parts in futre if I was to kill the precups again. |