URGENT! anti roll bar stuck! - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: 306 Repairs & Mods (https://www.306oc.co.uk/forum/forumdisplay.php?fid=22) +--- Forum: Suspension, Transmission, Handling & Braking (https://www.306oc.co.uk/forum/forumdisplay.php?fid=19) +--- Thread: URGENT! anti roll bar stuck! (/showthread.php?tid=30007) |
URGENT! anti roll bar stuck! - philpemberton94 - 08-04-2015 Attempting to lower my rear beam but the Arb is siezed pretty well, tried winding a bolt and it stripped the threads, don't have a slide hammer either. Any way of lowering it without removing the Arb? Cheers RE: URGENT! anti roll bar stuck! - welshpug - 08-04-2015 which side? should be doing the ths, with the correct threaded bolt you can lower without removing arb yes. RE: URGENT! anti roll bar stuck! - philpemberton94 - 08-04-2015 One side the threads are completely corroded and the one I tried just stripped, was the correct thread on the bolt, but it stripped, how would I go about lowering without removing the Arb? RE: URGENT! anti roll bar stuck! - bashbarnard - 08-04-2015 You cant arb has to be removed. If its that bad likely that the beam is shagged as well anyway. RE: URGENT! anti roll bar stuck! - welshpug - 08-04-2015 you dont need to remove the arb to lower. what thread were you using? RE: URGENT! anti roll bar stuck! - ConorTRG - 08-04-2015 Majority of arbs that I've tried to remove with a bolt have been useless, stick as big a diameter of a punch that you can fit in and a couple of good heavy thumps and it will come out. RE: URGENT! anti roll bar stuck! - Stef205 - 08-04-2015 Depending on the year of the axle some flags used m12x1.5 and from what ive come across the later axles used a m12.1.75 But there is no need to remove it to lower it. RE: URGENT! anti roll bar stuck! - philpemberton94 - 08-04-2015 Thread was m12x1.5 RE: URGENT! anti roll bar stuck! - bashbarnard - 08-04-2015 How do you get the torsion bars out without removing arb? I thought arb plate is in the way. Obviously I could be wrong and as Stef is saying it I probably am. RE: URGENT! anti roll bar stuck! - Piggy - 08-04-2015 Headbolt RE: URGENT! anti roll bar stuck! - Stef205 - 08-04-2015 (08-04-2015, 01:34 PM)bashbarnard Wrote: How do you get the torsion bars out without removing arb? I thought arb plate is in the way. Obviously I could be wrong and as Stef is saying it I probably am. Just turn the flag so it's out of your way, it's very accessible with them out the way RE: URGENT! anti roll bar stuck! - philpemberton94 - 08-04-2015 Gave up in the end, think my beam is goosed any way because it looks like there is some camber on the back! RE: URGENT! anti roll bar stuck! - bashbarnard - 08-04-2015 (08-04-2015, 02:21 PM)Stef205 Wrote:(08-04-2015, 01:34 PM)bashbarnard Wrote: How do you get the torsion bars out without removing arb? I thought arb plate is in the way. Obviously I could be wrong and as Stef is saying it I probably am. Now I feel like an idiot. Of course you could!! |