+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Photos and Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=20)
+--- Forum: 306 Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=3)
+--- Thread: Black Phase 1 DTurbo = Win. (/showthread.php?tid=1077)
Black Phase 1 DTurbo = Win. - silverzx - 24-01-2012
Updated Spec: 19/03/12
Lot of you know me already, thought I'd get a project up on here that I can keep track of.
Little background info: car started on a Lucas, loads of service history, heater matrix went within first week of owner ship so changed that, other then that a standard black DTurbo.
Spec to date - 26/12/12:
- FMIC (2.25" piping)
- Xantia inlet manifold
- Black Cyclones
- Gov'd/LDA'd Bosch
- T25 @ 28PSI (No Filter & welded WG)
- Straight through to Cherry Bomb
- 2 X Slim line fans
- Chavtastic sub woofer, amp, 6x9's etc
- 266 Brakes
Stored parts:
- Cone Air Filter x 2
- Xantia 2.25" black plastic & rubber piping
- 40mm lowering springs
- Throttle cable kit
- Lucas pump setup
- Bosch setup
- Manual boost controller
- EGR Blanking plate (Mark_Airey special)
- T2
Wanted parts:
- Bigger cone filter / BMC CDA
- Custom intake piping
Future plans are to get some bigger brakes on, get the FMIC plumbed in, turn the boost up to 24~30 PSI (along with increasing the fuel obviously) and possibly if funds permit pay someone to weld a bigger turbo on.
Heres an old picture, I need to get some new ones soon:
![[Image: 2.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/2.jpg)
The beast of a FMIC that arrived today (what have I done lol)!?
Can fits in the inlet/oulet:
![[Image: P1010015.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1010015.jpg)
Comparison against a beer:
![[Image: P1010016.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1010016.jpg)
Comparison against a 32" TV:
![[Image: P1010017.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1010017.jpg)
Any comments good or bad welcomed.
Re: Black Phase 1 DTurbo = Win. - D@wson - 24-01-2012
Thats beasty! Bet that cost you an arm and a leg.
Re: Black Phase 1 DTurbo = Win. - silverzx - 24-01-2012
D@wson Wrote:Thats beasty! Bet that cost you an arm and a leg.
You'd be surprised...
It didn't look so big in the advert.
It's defiantly bigger then the twin pass I had on my HDi anyhow (which I thought was a killer)!
In honesty I'm worried its not going to fit...
Heres a pic of my old HDi's twin pass:
![[Image: P1010943.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%203%20Pug%20306%20FMIC%20DTurbo/P1010943.jpg)
Re: Black Phase 1 DTurbo = Win. - silverzx - 27-02-2012
Update, running T2 @ 25 (ish) PSI and obviously up'ed the fueling.
Gotta 0-70 video short shifting before 5k obviously
.![[Image: th_P1030723.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/th_P1030723.jpg)
Also gotta video of me driving away from camera for the exhaust sound.
![[Image: th_P1030724.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/th_P1030724.jpg)
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 27-02-2012
Looks good mate! You lowering yourself?
Re: Black Phase 1 DTurbo = Win. - Mattcheese31 - 27-02-2012
looks like it's going pretty well that does . . . .
Re: Black Phase 1 DTurbo = Win. - silverzx - 27-02-2012
Cheers Matt.
Uh not sure Foxy, could do with a GTi6 beam before my MOT on 23rd as the drums are shagged anyway.
Not something I've done before though so don't really want to tackle a job I might not be able to finish.
Re: Black Phase 1 DTurbo = Win. - 4WayDiablo - 27-02-2012
Black ph1 is definatly win! :-)
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 27-02-2012
I can help you do it of you want just done mine an I've done a saxo before aswell!
Re: Black Phase 1 DTurbo = Win. - silverzx - 27-02-2012
Foxy-jim Wrote:I can help you do it of you want just done mine an I've done a saxo before aswell!
Really? That would be so sweet! :dance: Thanks. :mrgreen:
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 27-02-2012
Ye mate that's cool! I have all the tools etc. I can try and do it the proper way. If not will do it the notch method. That ok?
Re: Black Phase 1 DTurbo = Win. - silverzx - 28-02-2012
Sounds good to me!
I've got some 40mm springs, do you have a spring compressor by any chance?
Re: Black Phase 1 DTurbo = Win. - 4WayDiablo - 28-02-2012
Makes me wanna put a ph1 front end on mine! Haha
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 28-02-2012
I don't have a spring compressor, but I may look into getting some so that I can do more in the future.
Re: Black Phase 1 DTurbo = Win. - silverzx - 28-02-2012
Foxy-jim Wrote:I don't have a spring compressor, but I may look into getting some so that I can do more in the future.
Sweet, well my MOT is due on the 23rd of March so not planning on doing any major mod's until after that. So I'll keep you updated.
Really need some complete front brakes, will take 266 or 283's but must come complete for direct replacement.
Re: Black Phase 1 DTurbo = Win. - silverzx - 28-02-2012
Some pictures over the weekend:
1
![[Image: P1030727.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030727.jpg)
2
![[Image: P1030703.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030703.jpg)
3
![[Image: P1030699.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030699.jpg)
4
![[Image: P1030697.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030697.jpg)
5
![[Image: P1030728.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030728.jpg)
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 28-02-2012
Ye I want some new brakes, going to get 266mm as thats all I can get under my wheels!
Re: Black Phase 1 DTurbo = Win. - 4WayDiablo - 29-02-2012
Haha is that you hiding a dent that i spy?
Re: Black Phase 1 DTurbo = Win. - silverzx - 29-02-2012
4WayDiablo Wrote:Haha is that you hiding a dent that i spy?
Not at all mate.
Re: Black Phase 1 DTurbo = Win. - 4WayDiablo - 29-02-2012
Pics 2 and 4... looks like there is a dent above thw rear wheel :-P
Re: Black Phase 1 DTurbo = Win. - Pompey306mark - 29-02-2012
Looking good. Glad to see there are some good plans for the future.
Re: Black Phase 1 DTurbo = Win. - silverzx - 29-02-2012
I see what you mean, think thats just the way the cameras making it look. Theres defiantly not a dent there.
Possibly Mark, I just feel once I start chucking parts at it I'm going to be stuck with it.
As much as I like it I'd love one with less miles on the clock and better paint/body.
Sensible option is to keep it of course.
Re: Black Phase 1 DTurbo = Win. - Connor - 29-02-2012
4WayDiablo Wrote:Makes me wanna put a ph1 front end on mine! Haha
Ive got the parts minus a bumper
/shamelessplug
Re: Black Phase 1 DTurbo = Win. - Pompey306mark - 29-02-2012
all can be sorted with a bit of money and passion
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 29-02-2012
As mark said! Don't sell up! Just get it nice and low!
Re: Black Phase 1 DTurbo = Win. - silverzx - 05-03-2012
New purchase! http://www.ebay.co.uk/itm/140713443866
Image of new purchase:
![[Image: %24(KGrHqMOKj0E6mQp4CHVBOppPrjnIQ~~60_12.JPG]](http://i.ebayimg.com/00/s/ODk0WDEwMjQ=/%24(KGrHqMOKj0E6mQp4CHVBOppPrjnIQ~~60_12.JPG)
Need some recommendations on inlet manifold gaskets please guys. Am I right in thinking ph1 DHY would use a double gasket for exhaust and inlet or is it likely to be singles?
Cheers guys!
Re: Black Phase 1 DTurbo = Win. - ginge191 - 05-03-2012
when is this going to get some lows?!?
Re: Black Phase 1 DTurbo = Win. - silverzx - 05-03-2012
ginge191 Wrote:when is this going to get some lows?!?
Ask Foxy-Jim? :roll:
Re: Black Phase 1 DTurbo = Win. - Foxy-jim - 06-03-2012
Haha when are you free and when do you want it doing?
Re: Black Phase 1 DTurbo = Win. - silverzx - 09-03-2012
FMIC stuff arrived this morning!
![[Image: P1030804.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030804.jpg)
![[Image: P1030803.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030803.jpg)
![[Image: P1030801.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030801.jpg)
![[Image: P1030800.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030800.jpg)
![[Image: P1030799.jpg]](http://i467.photobucket.com/albums/rr40/shivannaz/Phase%201%20Pug%20306%20DTurbo/P1030799.jpg)