![]() |
Ph1 Estate. Gearbox mounted vnt - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: Photos and Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=20) +--- Forum: 306 Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=3) +--- Thread: Ph1 Estate. Gearbox mounted vnt (/showthread.php?tid=22302) |
RE: PH1 DT estate project "stock" - ash23 - 15-04-2014 as the facebookers would have seen this is the top engine mount standard issue 306 really [attachment=15425] quick bodge to stop the knocking and added the little chock to the buffers [attachment=15426] ohh and painted with galv spray dont moan about the pidgin poo was a quick job in me lunch time ![]() [attachment=15427] PH1 DT estate project "stock" - devils_fuel - 15-04-2014 Ash my car is dead so I've no need for the bumper now ![]() RE: PH1 DT estate project "stock" - ash23 - 15-04-2014 no probs mate shame to see her go tho ![]() PH1 DT estate project "stock" - devils_fuel - 15-04-2014 Yeah mate it is but when a car is not worth it, it's not worth it even if you love it ![]() RE: PH1 DT estate project "stock" - Chris_90 - 16-04-2014 Seen as your keeping this stock it really needs a big turbo! Oh and forged rods why your at it ![]() RE: PH1 DT estate project "stock" - ash23 - 16-04-2014 haha this is staying "stock" ![]() you got a big turbo on the vento yet ![]() PH1 DT estate project "stock" - devils_fuel - 16-04-2014 You got a vento Chris?? RE: PH1 DT estate project "stock" - Chris_90 - 16-04-2014 (16-04-2014, 06:58 AM)ash23 Wrote: haha this is staying "stock" No not "yet" ![]() (16-04-2014, 07:26 AM)devils_fuel Wrote: You got a vento Chris?? Yep ![]() RE: PH1 DT estate project "stock" - ash23 - 17-04-2014 done a few more little bits on the old girl to get her handling a little more like pug intended two new wishbones old ones were fecked both bushes had basically fell apart and ball joints had lots of play but this passed a mot just before I brought her and one front axle mount us in two pieces so as you jack it up the front of the axle comes away quater inch :O some dodgy mot ers out there shouldnt have passed at all. also replaced the cv boot on the drivers side as that chucked all its grease out ![]() also chucked in a powerflex lower mount will prob be coming back out tho the vibrations are ridiculous in my black dt I put a yellow one in and I made no difference to the vibration but this is silly hopeing for it to bed in alot ill see tho. and made up a strut brace with some spare steel at work why buy when you can bodge ehh ![]() ohh and she's in for tracking tomorrow ![]() [attachment=15531] [attachment=15532] the brace will be painted silver to match the car ![]() [attachment=15533] PH1 DT estate project "stock" - devils_fuel - 17-04-2014 Could have sold you my e-tech one lol RE: PH1 DT estate project "stock" - ash23 - 17-04-2014 not really a fan of thoses ones had one on my old dt use to be very bendy lol pluss mine didnt cost me anything in fact I got payed to make it ![]() PH1 DT estate project "stock" - devils_fuel - 17-04-2014 Lucky you being paid to make your own strut brace lol They don't bend if fitted and tensioned right ![]() RE: PH1 DT estate project "stock" - ash23 - 19-04-2014 got the brace painted and on looks ok ![]() ![]() [attachment=15577] [attachment=15578] [attachment=15579] comments welcome as always RE: PH1 DT estate project "stock" - Chris_90 - 19-04-2014 Needs lowering that arch gap is massive ![]() ![]() RE: PH1 DT estate project "stock" - ash23 - 19-04-2014 haha something may be sorted to give it a little less tractor spec ![]() RE: PH1 DT estate project OIL COOLER advice needed - ash23 - 24-04-2014 decided its about time I mounted the oil cooler im having pirtek make up some oil lines just need to decide on the mounting position so help is needed. its a non thermostat plate so I was thinking behind the rad to keep some warmth there? but can the cooler be side mounted or does it need to be mounted vertical? like this ? [attachment=15727] or like this? [attachment=15728] RE: PH1 DT estate project advice needed - Chris_90 - 25-04-2014 I say vertical RE: PH1 DT estate project advice needed - silverzx - 25-04-2014 About time you updated your signature! RE: PH1 DT estate project advice needed - ash23 - 25-04-2014 (25-04-2014, 10:57 AM)Chris_90 Wrote: I say vertical im unsure lol soo you recon with the outlets to the side rather than pointing up? sticking a new rad in tomorrow so going to get it mounted up along with the fmic ![]() (25-04-2014, 12:35 PM)silverzx Wrote: About time you updated your signature! haha I suppose it is just need a decent pik of the state first ![]() RE: PH1 DT estate project advice needed - Chris_90 - 25-04-2014 Yer it will act more a radiator that way with heat rising the cool oil will drop down to the bottom well that's how I see it might be completely wrong tho ![]() You got cover to do car? Might pop up but with weather it's given don't fancy getting piss wet though RE: PH1 DT estate project advice needed - ash23 - 25-04-2014 [quote='Chris_90' pid='424315' dateline='139844287 Yer it will act more a radiator that way with heat rising the cool oil will drop down to the bottom well that's how I see it might be completely wrong tho :lol: You got cover to do car? Might pop up but with weather it's given don't fancy getting piss wet though [/quote] makes sence ![]() na no cover but if its pissing it down ill not bother anyway lol but should be ok anyway have to let me know if your poping over mate RE: PH1 DT estate project advice needed - Chris_90 - 26-04-2014 some pics from today ![]() ![]() ![]() ![]() ![]() ![]() Random pic of exhaust tip ![]() ![]() RE: PH1 DT estate project advice needed - ash23 - 26-04-2014 Cheers chris . you like that tip ehh ![]() few more piks of todays efforts was meant to go to Combe but a shagged rad put a stop to that ![]() started like this [attachment=15751] one fecked rad [attachment=15752] [attachment=15753] I/c on forgot the in between pikss [attachment=15754] [attachment=15755] ware the pipes come to will get the rest plumbed in when I swap the turbo. [attachment=15756] simple mount chucked together for the new filter [attachment=15757] [attachment=15758] so the filter slips right in there rather than just being wedged in a corner somewhere [attachment=15759] oh and also ahd a look at makeing up a lower strut brace looks like it will be even easier than the top one ![]() c and c welcome ![]() PH1 DT estate project FMIC on - devils_fuel - 28-04-2014 Looks good mate, better the rad let go there than hammering it around Coombe ![]() PH1 DT GT20 estate project FMIC on - Sambarker - 30-04-2014 That a rover 200 fuel filter? RE: PH1 DT GT20 estate project FMIC on - Chris_90 - 01-05-2014 (30-04-2014, 09:42 PM)Sambarker Wrote: That a rover 200 fuel filter? It looks the same as the one my vento. Gt20 on the title??? Hmmmm ![]() RE: PH1 DT GT20 estate project FMIC on - lolsteve - 01-05-2014 If you're getting paid to make strut braces then you mind slapping one together for me ![]() ![]() As said needs lows though also loving the use of cable ties, reminds me of my old intercooler system L series fuel filter? RE: PH1 DT GT20 estate project FMIC on - ash23 - 01-05-2014 (30-04-2014, 09:42 PM)Sambarker Wrote: That a rover 200 fuel filter? honestly havent got a clue picked it up from a local motoquip can get the part no if needed? (01-05-2014, 10:47 AM)Chris_90 Wrote:(30-04-2014, 09:42 PM)Sambarker Wrote: That a rover 200 fuel filter? really ? dont know why the title would say that ![]() (01-05-2014, 11:42 AM)lolsteve Wrote: If you're getting paid to make strut braces then you mind slapping one together for me haha id need the car with me tho ![]() filter could literally be off anything lol as were talking about braces did the lower brace today not the prettiest but will do the job [attachment=15877] RE: PH1 DT GT20 estate project FMIC on - ash23 - 02-05-2014 fitted the lower brace tried to paint it but ran out so atacked it with stickers I know they wont last but neather does the paint lol [attachment=15893] [attachment=15894] and wheels back on the ground plenty of room for lowering ![]() [attachment=15895] pollished lda cap couldn't let it go to waste hehe [attachment=15896] RE: PH1 DT GT20 estate project FMIC on - lolsteve - 03-05-2014 Looks good, nice and strong. Does the lower brace make much impact when you already have the upper brace? |