306oc - Peugeot 306 Owners Club & Forum

Ok so having abit of a (well a large one) garage clear out, most of this will get chucked next week if no one is interested, and what has interest I can either offer local pickup (grantham) or can take to FCS. These things have been kicking about totally unused for years.

HDI Head - cam has been out of oil, this is reflected in price mating surface fine £40



T25 Turbo - Oil Seal gone so weeps, but minimal play in shaft in/out up/down £10



Tyre, unused 175-65 R14 £5



205 Towbar + electrics £30


Guillotine chunky bastard £20



Black & Decker Workmate £20



T25 - Melted tips, could be useful £5


Stihl Hedgecutter (think its 32" and has 49cc) £60


Flymo Mower, comes with extension cable £15


Hub pullers the set £10


Riveters £2


Gas flashback resistors (gas side & oxygen side) £25


Pneumatic Impact Driver, works fine has stood the test of time £15



Toolset, pretty much unused, made by silverline £5


11x grease tubes, unopened 4.4kg £15



X-Army Jerry Cans £10 each


Reel of copper wire, looks like 15 amp or so, cant be sure £3



Inline Air tool lubricator £15


Microswitch £2


Hydraulic Ram and control unit - 700 BAR - £45


Single Small Ramp £4


EGT Probe £5


T2 Turbo, minimal play when dry, no hotside £20



As said earlier, all this stuff is gonna get binned probably within the week but will hold for anyone interested thats going to FCS, or anyone who wants to local pickup, have binned alot of things today that probably should have gone on here, its time time! car needs an MOT garage needs clearing I miss boost! My arm may be twisted for posting but much prefer local pickup/fcs etc.

Will be putting some other things on shortly once I move to clearing the next shed... will include slimline fans, FMIC, xantia mani, silicone pipes, starters, alternators, PAS pumps, TMIC's, hdi rods, exhausts so keep posted!

Any questions PM me

Dave

I'll have the socket set! FCS pickup?

Sweet, will pm you my phone number!

Could be interested In the xantia Mani hen it comes up

can i have some more info on the hydrolic kit!
type of ram is it spring return or is it powered both ways (single or double acting) part number?
is the pump just a pressure pump with a resovior has it got control valves on it (single or double acting) part number
any pipework to connect the ram?
collection from FCS is possible and if its sutable thanks

I Will take the hub pullers at fcs. are you camping sat?

f*ck, would have taken the socket set... Dammmit

Id be interested in slimline fans (if a pair), the FMIC and some silicones depending on sizes conditions and prices.

Im sure I could pursuade someone to bring it back from FCS for me.

Could be interested in the egt probe. Is it any good, dont want it falling apart into my turbo lol.

Alright chaps been abit busy lately, sorry for the late responses & PM's

4WayDiablo Wrote:Could be interested In the xantia Mani hen it comes up

Was going to keep it as a complete FMIC setup really, but will see if I can find all the bits... same goes to dum dum.

cully Wrote:can i have some more info on the hydrolic kit!
type of ram is it spring return or is it powered both ways (single or double acting) part number?
is the pump just a pressure pump with a resovior has it got control valves on it (single or double acting) part number
any pipework to connect the ram?
collection from FCS is possible and if its sutable thanks

Its a double acting, part number for the ram is shown below. Its a pressure pump with control valves in the end for ram in/out movement, its practically band new & unused.





There is no pipework, but shouldnt be much from a local hydo shop. May be able to fine some generic 1m ones, but cant promise i'll be able to find them, only fittings will be needed if I find these, but as said pipes are relatively cheap anyway.

puglove Wrote:I Will take the hub pullers at fcs. are you camping sat?

Yes, i'll be camping fcs and i'll bring them along, PM'ed

londondan86 Wrote:Could be interested in the egt probe. Is it any good, dont want it falling apart into my turbo lol.

Sorry mate, already promised to Mr Barker Sam, you have PM now btw, sorry late reply.

ginge191 Wrote:f*ck, would have taken the socket set... Dammmit

Sorry chap, Johnny81191 has first dibs at FCS.

I dug a load more crap out the other shed, but will probably get these up in another thread! including wheel bolts and studs.

Dave

Your probably best selling the FMIC as a whole mate, thought you had the silicones and that as spares. GLWTS

for Cully: