306oc - Peugeot 306 Owners Club & Forum

Full Version: Clearout (Help fund my rods!!!) Now on ebay
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Afternoon peeps, first post for a while, hope everyone is ok Smile

Time to clear out some hoarded parts so I can get my project rolling again!

1. 6 front brake setup - Calipers, discs, pads - £50
Currently painted yellow but paint is chipped and could do with redoing if fussy (I could give them a fresh coat of hammerite for some extra cash on top) Discs are almost new, small amount of surface rust which will come off when used. Pads have loads of meat left too! Also have some braided lines which I can put with this to make a full kit.
[attachment=16914]

2. Black angel eye headlights for P2/3 - £60
[attachment=16870]
[attachment=16869]

3. XSI - GTI inlet manifold conversion kit - £50
Everything included except new gasket
[attachment=16917]

4. Nissens radiator - £50
This has the later type P3 connector, mint condition.
[attachment=16915]
[attachment=16916]

5. Apex Shocks/Springs - SOLD
Were fitted to my d turbo before I put the coilovers on. These are very low ~60-80mm drop. Look really good though!! Already fitted on top mounts so no spring compressors required on fitting, just bash them straight in - 1hr job!! Big Grin
[attachment=15476]
[attachment=15477]

6. Clock with temp display - £5

7. GTI 6 Alcantara rear seats - £15
Still have the fronts in my car at the moment but will sell the lot complete if someone brings 2 decent front seats with them Smile
Rears are in good condition with no rips or tears.

8. P2 twin optic head lights - £10
These came off the cabby and are in fantastic condition.

9. Gti 6 Master Cylinder (23mm) - £20
Fully working 2 port abs MC

10. DT front calipers (247mm) - £10
Removed for upgrades, working well

11. P2 front and rear bumpers in black - £10 for the pair
Bit battered from storage

All prices exclude postage as I would rather cash on collection
First post updated Smile
Bump!!
Don't spose you have a posted price on the springs and shock?
^£55 posted?
50 and I'll pay right now haha
(17-06-2014, 01:31 PM)sherman306 Wrote: [ -> ]50 and I'll pay right now haha

pm incoming Wink

Springs sold!
12. I have 2 sets of hubcentric spacers, stud conversion type
Set 1 - £50
Everything included, with tool
[attachment=16918]
Set 2 - £40
Missing a couple of bolts and nuts, no tool
[attachment=16919]

13. HDi Injectors - £10
Spares/repairs - these came off my HDi as they were really noise and were not injecting correctly although when they were removed there was an incorrect copper seal fitted which could hav been the problem all along. Worth a test, if not ideal to have referbed while still using your own.
[attachment=16921]

14. XUD Inlet adpter - £30
Painted in hammerite "hammered black". Fits to stock manifold.
[attachment=16922]

15. Auto - dimming rear view mirror - £20
Bought on here last year and never fitted, from a 406 maybe?
[attachment=16923]

16. T2 Turbo - £25
Good condition, no unexpected play
[attachment=16924]

17. TD04 CHRA - £30
This was fully rebuilt with new seals, bearings etc. Unbalanced but care was taken during dissasemby. Fine for xud usage!
[attachment=16925]

18. Stage 1 ECU & BSI - £30
This belonged to HDI-Kyle and was dyno'd at 130bhp. Never fitted myslef, just sat on the shelf gathering dust!
[attachment=16926]
Bump!! Open to offers on everything, worst I can say is no so try me!!! Otherwise stuff will be going on egay!
Final bump before the lot goes on ebay tomorrow. £10 off everything up there (unless it is a tenner or less already, I'm not paying you lot)!!
Is the td04 ready to go mate? £25 posted?
Does the Stage 1 ECU also come with the key chip ?
Is is a Bosch ecu and what code is it please?

Cheers Titch
How thick are the spacers? 20mm?
(25-06-2014, 06:55 PM)doogle-d turbo Wrote: [ -> ]Is the td04 ready to go mate? £25 posted?

Yes mate, ready to put into your existing housing. £30 posted?

(25-06-2014, 09:08 PM)titch Wrote: [ -> ]Does the Stage 1 ECU also come with the key chip ?
Is is a Bosch ecu and what code is it please?

Cheers Titch

No key but this can be coded with pp2k. I'll update with the codes when I get back tomorrow.

(26-06-2014, 10:15 AM)Kezzieboy Wrote: [ -> ]How thick are the spacers? 20mm?

Yea 20mm matey Smile
(25-06-2014, 09:08 PM)titch Wrote: [ -> ]Does the Stage 1 ECU also come with the key chip ?
Is is a Bosch ecu and what code is it please?

Cheers Titch

No key but this can be coded with pp2k. I'll update with the codes when I get back tomorrow.

Ok cool, will see if it is the same as mine, will then have to look into how to get it to run on mine as i don't have pp2k
Interested in a pair of the spacers...

Dont need any bolts though...

How much posted and are they 20mm?
Hmm, how much arch rolling will be required to get my wheels on with 20mm spacers Tongue
(26-06-2014, 09:12 PM)Piggy Wrote: [ -> ]Interested in a pair of the spacers...

Dont need any bolts though...

How much posted and are they 20mm?

Yep 20mm mate. £40 posted?


(26-06-2014, 11:02 PM)Kezzieboy Wrote: [ -> ]Hmm, how much arch rolling will be required to get my wheels on with 20mm spacers Tongue

I had to roll the inner lip to clear the challengers that's it.

ECU details

[attachment=17229]
nice one , 249, i will check mine in the mornng.
You at pugfest?
(28-06-2014, 09:04 PM)titch Wrote: [ -> ]nice one , 249, i will check mine in the mornng.
No probs pal

(28-06-2014, 09:19 PM)Piggy Wrote: [ -> ]You at pugfest?
Afraid not mate, bloody broke at the moment.
What happened to the shell out if interest?
(30-06-2014, 07:49 AM)Matt Wrote: [ -> ]What happened to the shell out if interest?

Shell?? Lol
Now on ebay all 99p start so some potential bargains to be had! The rest will be going on tomorrow.

http://www.ebay.co.uk/sch/londondan86/m....7675.l2562